Feel free to ask any PLC RELATED question here. If you know the answer to an existing question, help everyone by posting an
answer.
Enjoy!!!
Hello,
I am a Sunday School Teacher in my spare time. At a young age we begin working with our kids in attempt to teach the Books of the Bible...
How do you install update on Red Lion Crimson ver 3.1. Do I just need to run the exe file on the host server?
Hi,
Is it possible to for an RIO with Flex 5000 series module, e.g. 5094-AEN2TR, to communicate with an 1756-L72E processor.
Hello everyone, I'm new here.
First of all I just want to say that you guys are very knowledgeable and reading your posts on here has saved my...
Hello I have In touch 10.1
I tried to enter the WindowMaker to make some adjustments I am using a dongol for the license . I can access the...
I have been trialing a Proxmox based development server for my group but have had no end of troubles with the several instances of VM I have...
Hi all.
Simple as simple can be, I don't understand what's happening.
I'm toggling he OSR on, GX_LUB_PUMP1_LEAD should switch. It doesn't.
The...
I hope there is someone out there that can help. I recently inherited 35 Magnum presses (circa 1995) that have GE Fanuc Series 90 micro PLC's...
Dear team,
We are constantly facing M07 incremental loss on one of our kinetix 6500 safe torque.
We have changed Servo motor (MPL-B4530K-MJ72AA)...
Hello,
My associate and I are trying to sync up two ControlLogix racks (7-slot chassis) with identical modules. We are able to see the secondary...
My current situation is a follows:
I have two similar 1769 controllers with similar programs. Both have a UDT array that is being used to store...
I've posted this on the ptc forum as well, but no luck with an answer (waiting for my service contract number)
I keep getting the following error...
Hello All,
Was hoping I could get a little help with Modicon ladder logic. This is the first time I have seen Modicon logic and currently trying...
Currently I’m using ESA model VT155W0000 HMI and it’s communicate with Fanuc PLC. Can any one suggest can I convert ESA model to EXOR HMI eSMART07M
Have a system that has been running for over a year and all of a sudden getting a ExcessiveVelocityFault on one of the drives when the MSO command...
I'm starting learning ladder programming.
I bought the FX3U kit + coolmay HMI from aliexpress.
I'm doing basic testing and uploading codes.
I...
Hi,
we are using Rx3i CRU320 redundant PLC system and we noticed a discrepancy between Primary and Secondary controller.
Couple of variables (DI)...
I have a CompactLogix 1769-L31 and need to communicate with it. I only have studio 5000 on my computer. However, when I try to start a new project...
So I had an odd request from a customer for the above. I have written the logic and tested it all in one PLC with only using 7 outputs and 7...
I have an application using an incremental encoder and then I convert it to degree (0-360) using calculation program. For a while, the calculation...
Trying to setup a message read via Ethernet.
I have the path setup as 1, 1, 2, 192.168.66.10
I get an error code 1, ext err 315.
I am beating...
Hey.
If you haven't already read me, first time I'm building a full project on Rockwell PLC.
I started building the sequences last week and I...
Hi!
Have anybody the VLT DIALOG SOFTWARE? This soft is used for setting parametrs on Danfoss converter.
Thanks in advance if you send it me...
I have been requested to test this proportioning valve for PLC control of flow/pressure.
Dwyer Series SVP Proportioning Solenoid Valve
The flow...
I'm trying to convert an RS Logix 500 fille when I open the 500 file and try to "save as" a .slc file, it does not allow it. It says " SLC library...