LIVE PLC Questions And Answers

Feel free to ask any PLC RELATED question here. If you know the answer to an existing question, help everyone by posting an answer. Enjoy!!!
Dear All I have a Laser on my table where I communicate via Putty over Ethernet IP I have setup the Putty with a RAW connection and an IP...
Replies
38
Views
8,896
Good morning. I'm doing a rehab and I need to recycle some part of the old code that won't change and that I need. This is a calculation that...
Replies
22
Views
1,129
Maybe this is just not possible, or maybe I am doing something wrong. Background; I have a data array of over 1500 products. For sorting I...
Replies
6
Views
705
Hi All, I'd like to know how to show 100 days of Alarm in the Alarm Summary in Aveva (Intouch) SCADA. I couldn't find any option like that in...
Replies
10
Views
750
Hi guys, I am looking for a good replacement for an Omron smart relay. A customer of ours has a couple of these and they are beginning to fail. As...
Replies
14
Views
1,050
Hello colleagues, I have HMI which is running on FTView studio SE. Recently i introduced an analog signal for a Hydrogen analyzer and wanted to...
Replies
1
Views
270
Im trying to get data from AB guardlogix controller using Kepware in a remote location but it seems that version 6 can only support contrologix...
Replies
2
Views
398
I want to buy used/inexpensive (under $500) PLC hardware and software for personal use/testing. Can any of you suggest the best way to go about...
Replies
46
Views
4,513
Hello, I want to establish LTE communications (2 S7-1200) with common Workstation. All i have is 1200CPU with 6GK7243-7KX30-0XE0...
Replies
0
Views
257
I have an L24ER-QB1B with a 1769-ASCII card in slot number 4. I'm looking to send data to this zebra printer after every completed sequence. I'm a...
Replies
2
Views
380
So first off I know everyone hates directly answering safety questions and I want to start by I will take no ones opinion as rule but looking for...
Replies
12
Views
1,294
I don't know if this is the right place for the subject at least I'll try. The company has one of the oldest computers that is a master Windows...
Replies
5
Views
683
Hey guys, We are facing an issue, Krones hotfill line, around 10-15 fillers out of 110 are overfilling the bottle. Please help us what can...
Replies
13
Views
479
Hi am new to TIA and i have a challenge when i archive the project it;s being saved as PDF. How to l change from PDF to normal TIA. Your...
Replies
3
Views
542
Hi all, I have a project I am working on with a E810-0015 VFD. I am switching between Vector Speed Control and Position Control (Pr.800)...
Replies
0
Views
206
hi all i ask about the ignition SCADA it is strong or not and what is the advantages and disadvantages of it ??
Replies
16
Views
7,605
We had a new installation with Control Logix L81 which uses 2 of the 1756-IR12. Using Studio 5K Ver.30 We are facing no readings at the terminal...
Replies
2
Views
1,770
What's your go to 4-20ma isolator. I've got some 4 wire 4-20ma from several flow meters and scales that I would like to isolate before it gets to...
Replies
10
Views
1,589
Getting T01C61 fault on L83ES processor with studio firmware 32.03 and PLC firmware 32.013. It wipes the program out, re-download the program and...
Replies
1
Views
485
Hi I am being given several fault words (as a DINT) from a Drive that I am receiving into a Compactlogix L33ER controller. I have a small...
Replies
12
Views
1,061
Good afternoon. Below is the network diagram, according to which I wanted to configure supervisor on en2tr module. Stratix is in RSTP mode, due to...
Replies
4
Views
504
HEllo, still satruggling with the curse WinCC Unified. See attached picture. I just want to change the fill colour from turqoise to grey and then...
Replies
5
Views
382
Hello to everyone, I need to comunicate With a Modbus gateway(TCP-RTU)connected throught Modbus TCP/Ip on wincc v7.5 or professional; i will...
Replies
0
Views
220
Hello All, is there any way to fetch remote controllers Mode Run/Remote Prog/Faulted etc. ( AB L8 Series) using CIP message, if yes please share...
Replies
5
Views
754
Hi All, I have a programming background but have never used a PLC. I have what I think is a simple automation project however Im not sure of the...
Replies
19
Views
1,731
Back
Top Bottom