6es5 308 3UC11

isteak007

Member
I
Join Date
May 2009
Location
NewYork
Posts
216
My PLC S5 155U Cpu 948. while i load the program to CPU CPU Run light is on.

But when i attached profibus cable in CP Card Module (6es5 308 3UC11)

PLC Stopped.

So i guess problem is not in PLC,

So How can i check my all profibus station in S5,
I heard a software called Profinet or something
Can anyone give me any information

Thanks
 
moggie said:
The software needed to configure/program the IM308 is COM PROFIBUS

What LED's do you get on the IM308 ?
Has the IM308 been configured correctly?

From the Siemens web site

http://support.automation.siemens.com/WW/view/en/1498610
Click to expand...

When i load my program to Cpu.
Cpu is going to run mode.
My CP card has a eprom.
But when i connect cable to CP card after 13 or 14 seconds
PLC is going to Stop Mode
and stop light is blinking.

When I attach my machine profibus cable to PLC's CP card after 13 or 14 Second PLC is going to Stop mode.
And Cp Card all light is blinking and cp card has a eprom and i think cp card is ok.
So how can i find the problem device using ComProfibus V5.1?

Thanks

Thanks
 
Is this a new system (as new as it can be with an S5 :) ) or did it work before? Do you get a QVZ error on the PLC?

As far as I remember there is no diagnostic tool integrated in COM Profibus.
 
isteak007 said:
When i load my program to Cpu.
Cpu is going to run mode.
My CP card has a eprom.
But when i connect cable to CP card after 13 or 14 seconds
PLC is going to Stop Mode
and stop light is blinking.

When I attach my machine profibus cable to PLC's CP card after 13 or 14 Second PLC is going to Stop mode.
And Cp Card all light is blinking and cp card has a eprom and i think cp card is ok.
So how can i find the problem device using ComProfibus V5.1?

Thanks

Thanks
Click to expand...

Check your S5 program to see if the IM308 standard function block has been used, if so this may give an error code.

See section 10.3.3 in the manual for meanings of error codes.
Also see section 3.4 onward for meanings of LED's
 

Similar Topics

S
6ES5 840-7SG01 and 6ES5 840BC21
Hi, I'm looking for standart function blocs SIEMENS S5 6ES5 840-7SG01 for IP262 and standart function blocs SIEMENS S5 6ES5 840-4BC21 for PID CPU 103
Replies
2
Views
1,204
serge maletras
S
I
6ES5 262-8MA13 Replace
Hello Everyone, i have a machine which has a module "6ES5 262-8MA13" installed Recently this module got defective. now i want to replace it with...
Replies
0
Views
1,425
isteak007
I
M
programming siemens s5 cpu 6ES5-922-1AA11
Hello First...alot of thanks to everyone help in this great forum... Second: I wanna program siemens s5 cpu 6ES5-922-1AA11... what I need for...
Replies
3
Views
2,303
goghie
G
M
6ES5 250 1AA11 CRT Video module step 5
Hello I searched for datasheet "manual" for this module : 6ES5 250 1AA11 ,, and I didn't find anything... Where can I find pdf for this module...
Replies
2
Views
1,814
JesperMP
JesperMP
A
Remplace CPU-6ES5-921-3W14 by 6ES5-922- 3UA11
hello, I have a machine tool HS, CPU-6ES5-921-3W14 (1982) sinumerik is defective, I have in stock the simatics 135U CPU 6ES5-922-3UA11 (1991), I...
Replies
0
Views
1,342
alan1968
A
Back
Top Bottom