GE Versamax micro 64

fred29

Member
F
Join Date
Jul 2011
Location
LA
Posts
16
Hello I have a versamax micro PLC that I'm trying to connect to my PC.
I'm going from the PC to a serial device server to the PLC using a RS-232. But
I can't get a connection can anybody tell me what I'm doing wrong
 
Tell us what you are doing and someone will be able to tell you where you may be doing something wrong.
 
GE Versamax

I'm trying to get the PLC to connect a robot picker. When I connect to Proficy
mismatch error an a not Equal. I'm thinking that's why I can't get it to connect
to the PC an PLC to Connect
 
fred29 said:
Hello I have a versamax micro PLC that I'm trying to connect to my PC.
I'm going from the PC to a serial device server to the PLC using a RS-232. But
I can't get a connection can anybody tell me what I'm doing wrong
Click to expand...
What port on the PLC?
What cable?
What settings?
What is the exact error you are getting, and when?
 
I'm using a RS-232 cable with a ethernet end going to the plc.
The setting that I have is 8 none none and 1
On Proficy I'm getting mismatch error an a not Equal
On the PC that control the robot I can't get any kind of connection at all.
I go to telnet to see if I can connect to the PLC an still on luck
 
fred29 said:
I'm using a RS-232 cable with a ethernet end going to the plc.
Click to expand...
Sounds right!
fred29 said:
The setting that I have is 8 none none and 1
Click to expand...
That is only the parity, Baud by default i think is 19200/8/ODD/1 the first part is important also!
fred29 said:
On Proficy I'm getting mismatch error an a not Equal
Click to expand...
On the Logic or the Hardware Config?
fred29 said:
On the PC that control the robot I can't get any kind of connection at all.
Click to expand...
The baud rates need to match and the pinout of robot's serial port must be correct
fred29 said:
I go to telnet to see if I can connect to the PLC an still on luck
Click to expand...
Did not know that was possible, unless its used on the robot....then thats why i didn't know....
 
fred29 said:
I'm using a RS-232 cable with a ethernet end going to the plc.
The setting that I have is 8 none none and 1
On Proficy I'm getting mismatch error an a not Equal
On the PC that control the robot I can't get any kind of connection at all.
I go to telnet to see if I can connect to the PLC an still on luck
Click to expand...
Please do not take this wrong.
I believe that you will be better served by having someone come in there to help you.

Local Product Support can be provided by your local Rep or Distributor. Click here to find your local support contact.
 
I can connect to Proficy but I can't connect to anything with the RS-232 not
even through hyperterminal
 

Similar Topics

B
GE Versamax micro:"OK led" down by going online
I do have a problem with a GE Versamax micro PLC. By going online (on Port 1) the "OK led" goes down. Power led stays On Port 2 no reaction at...
Replies
4
Views
389
BlackBoxRobotics
B
S
GE VersaMax Micro-64 PLC Ethernet Option Module IC200UEM001
Hi, I am trying to set the IP address on the IC200UEM001 Ethernet Option Module. I am following the procedure in the manual for setting a...
Replies
1
Views
428
sp_
S
B
Unable to communicate between Versamax Micro and Redlion Data Station Plus
Can anyone help me getting this comms connection set up? I am using Port 2 on the Versamax ICU200UDR005-DK, set in SNP with port settings Baud...
Replies
4
Views
1,545
Steve Bailey
Steve Bailey
C
I have problem about VersaMax 28-Point Micro PLCs
I want to simulate time in PLC to check the sequenced control Loop that separated by timing such as 8 pm, 9 pm . Please help me how to simulate...
Replies
1
Views
1,149
Steve Bailey
Steve Bailey
L
GE FANUC VERSAMAX Micro Controller
Hi. I have an Ge Fanuc Controller versa max and need to know where i can download the software for this PLC, anyone that can direct me please. I...
Replies
2
Views
1,207
LionHeart
L
Back
Top Bottom