Slc-500/03 dh485

jara

Member
J
Join Date
Jul 2010
Location
Cordoba
Posts
100
Hello everybody

I have a doubt and I don´t find the answer reading the user manual.

I would like to know if is possible to do the next, see the picture, change the panel view for my SLC500, and if is possible is the same cable? Can I do it?

282hwn8.jpg


Thank you very much
 
If I understand your question, you want to remove the PV and install a SLC5/03?

Then the answer is yes the same cable should work. 1761-CBL-AS09 0r AS03.
 
Today I have made the cable following the pinout that I found here
http://www.plctalk.net/qanda/showthread.php?t=45862
Thank you!

The problem now is with RSLinx. If I don´t choice Auto-configure I have the following parameters
Baud rate: 19200
Parity: None
Stop Bits: 1
Station Number: 00
Error Checking CRC
Protocol: Full Duplex

But I don´t find my SLC and if I try with Auto-Configure the next failure appear

zlw76.jpg


Any suggestion is welcome.
 
If you are plugged into the RJ45 port of the SLC5/03 that is a DH485 port. You need to use DH485 protocol driver in RSLinx.

If your PC has a real serial port then use the 1747-PIC/AIC+ driver. If not then you will need a USB to DH485 converter 1747-UIC.
 
Thanks again for your advised Mickey!

Yes, my PC have a real serial port,let me asked one more question, I need 1747-PIC or 1747-UIC device? Or have I to choice the driver 1747-PIC/AIC+ in RSLinx drivers?
I was looking for some information and I found this http://forums.mrplc.com/index.php?showtopic=19081 that is the reason why I tried with RS232-Df1 drivers.

Thank you again
 
Do you have a real serial port on your PC?

What operating system are you using XP service pacK? ?

Is RSLinx running as a service?

There are a few other reason why that old driver may not work see pdf's below.
 

Similar Topics

S
SLC 500 DH485 Link Coupler nodes
Hey everyone, I'm just looking for some input on the the network architecture when dealing with DH485 through the 1747-AIC Link Couplers. First...
Replies
0
Views
4,694
SiriusMark
S
M
SLC-500 SQO info wont go through mask
I have a program that I've used 100 times. SQO settings: File N7:0, Mask 0FFFFh, Dest B3:1, Control R6:0, Length 8, Pos 2. Length & Position...
2 3 4
Replies
48
Views
957
drbitboy
drbitboy
J
Slc 500 software & Siemens plc question
Everyone, i am in the process of purchasing the Slc 500 version of software to support what we have and i have a question. Several of our...
Replies
9
Views
766
James Mcquade
J
C
Slc 500 data question
In a slc 500 plc I am trying to move data with out using a lot of moves. I want to move data from n7:1 to n7:2 and data that was in n7:2 to n7:3...
2
Replies
16
Views
1,355
OkiePC
OkiePC
S
SLC-500 DeviceNet Scanner: Extract
Customer has a circa 2004 SLC-500 PLC. Fieldbus is a 1747-SDN DeviceNet scanner. Customer has SLC-500 file (.rss) with no comments. Has no *.dnt...
Replies
7
Views
553
S1ack
S
Back
Top Bottom