Feel free to ask any PLC RELATED question here. If you know the answer to an existing question, help everyone by posting an
answer.
Enjoy!!!
- Locked
- Sticky
Hi folks,
If you're having any login issues kindly send an email to [email protected] or use the 'contact us' link on the bottom of every page to get...
I'm working on learning OOP coding for TwinCat 3. I'd like to transfer and optimize the code my company has from AB Studio 5000 to ST TwinCat 3...
Hi,
Seeking consultation on an implementation matter, and have a question about Modicon Compact 984 communication through RS485:
Three Modicon...
Hello, I have a panelview plus that reads from 4 different PLC's. 2 of these used to be Micrologix PLC's and someone else went and updated them to...
Good afternoon, I have a problem communicating with a system, I will explain it briefly.
I have a HIS -ML17- CTBH monitor connected to an...
Hey Folks.
I have many of these Micros in the field now. 810, 820 and a couple 850. Probably about 12 or so. All in use 24/7. This is the...
I feel like this is probably a very simple thing I am overlooking.
(Compact Logix Studio 5000)
This is my first time using the predefined...
I have never had the pleasure of working with a "Thermistor" until now and have a question. The Thermistor is a 10KOhm 4-20mA 2-wire device and I...
I have a slc500 plc 1747-L30A. Using a communication cable 1747-PIC cable box combination. Running a version of software from DOS on a Windows 3.1...
Hello all, I have a 1756-EN2TR dual-port Ethernet IP Module attached to my 1756-L73 PLC. I currently have hazard symbols over both the top and...
Hello,
I am working with cimplicity workbench, I have made changes to the current project from this machine I am using in the past. However when...
Hello,
I have a CPU 317-2DP Firmware Version V2.1.8.
In TIA Portal only V2.6 is available, and there is no option to upgrade FW.
Then I open it...
Hello all,
I am an Industrial Electrician, and deal with a little bit of everything including PLC troubleshooting and programming. When I started...
I have a 90/30 CPU331. I am trying to upload the program out of the CPU and keep getting an error uploading the logic. Error 8262: Error...
Hello all I was trying to autotune a Kinetix 5100, I got an encoder fault and it says to check the wiring. I remove the 24 volts from drive to...
Hi All,
So I have a main routine with an instruction that's executed by XIC "Run"
I have a JSR located on a rung below it. In the logic for that...
Hello, doing switch from FBD to ST.
First task is converting my old work.
How do you sum variables?
For example, Interlock1, interlocl2 and...
Good morning everyone I’m currently working on a omron device net and have a nord drive that fell off the network. I have limit knowledge in...
HI everyone,
i am new to Siemens plc programming and i am in need of some help.
yesterday we had an S7-1200 CPU 1214C fail to turn on an output to...
Hello everybody,
I have Kinetix 5500 (2198-H040-ERS). I'm having issue with this drive. (I believe it's the drive/Kinetix and need confirmation)...
Hello All!
I am writing today because I cannot figure this out for the life of me. Another site I am affiliated with keeps having their slc 5/03s...
Decided to come to you all to see if any of you have any ideas on how to approach this issue.
I have a 'pack' of product that drops. When that...
Hi all,
I am having issues accessing my Cimplicity software - the site code changed after re-install and I am no longer able to attain a new key...
I am currently working on a project involving Cimplicity 10, which consists of a setup with two redundant servers and five operator workstations...
Hi guys, I need help with position control using a Veichi AC Servo Drive model SD600A1-T2-2R2. How do I know how many pulses for it to rotary 1...
Howdy everyone,
My company has a few machines running on SLC500 based PLC, and everytime it makes a part we count up on the counter which gets...