AutomationTechBrian, blperkins, Hossamhegab, JChick, sigmadelta, swimmy67

plcman2, JesperMP, Eric Nelson, MarkNightingale, jgreenewv, Steve Bailey, Ken Roach, Steve Etter, boneless, dcooper33, bernie_carlton, gmferg, Christoff84, JeffKiper, sthompson, kolyur, daba, iant, geniusintraining, RheinhardtP, jrwb4gbm, TheWaterboy 

Hi Folks, Effective immediately there are now 3 forum layout styles for you to use. By...
Started by: Phil Melore (July 26th, 2020)

August 4th, 2020 01:51 AM
by kalabdel

Hello Forum, I am developing a Pump Control System and one of the most important modes of...
Started by: rzuhair (July 21st, 2020)

July 31st, 2020 05:53 PM
by Tom Jenkins

First off, I am very new and green to working with PLC's. I have a MicroLogix 1400. I set it up to...
Started by: clkou (July 31st, 2020)

July 31st, 2020 04:35 PM
by Picklemon

I am receiving the following error message on the Simatic OP17 $545 DB 32b 41 3 not...
Started by: lsam (July 27th, 2020)

July 31st, 2020 03:14 PM
by lsam

I'm searching around trying to find an equation i can punch into my AB 1769 processor. I have a...
Started by: Dariusincj (July 31st, 2020)

July 31st, 2020 02:09 PM
by drbitboy

I'm looking at bidding what seems to be some standard pump controls for a local levy. The one thing...
Started by: sparkie (July 24th, 2020)

July 31st, 2020 01:46 PM
by ERCfarcontrol

Consider two control panels 100 meters apart. Customer is to run fiber between them so the PLC can...
Started by: agarb (July 28th, 2020)

July 31st, 2020 12:26 PM
by agarb

I just got AutoCAD installed on my computer and want to become more well rounded in it. I was...
Started by: MattMatt9 (July 31st, 2020)

July 31st, 2020 12:15 PM
by passwordg

Excuse my ignorance but I am having a hard time figuring out where my real IO points are to address...
Started by: kandymann (July 31st, 2020)

July 31st, 2020 11:38 AM
by kandymann

Is the drive missing something or my computer?
Started by: MattMatt9 (July 30th, 2020)

July 31st, 2020 10:50 AM
by dmroeder

Good Morning , Had a PowerFlex 70 go bad . Uploaded the parameters to the HIM . Did not...
Started by: Cydog (July 31st, 2020)

July 31st, 2020 10:44 AM
by drforsythe

Dear Experts, Need your suggestions. I am to take up an upgradation project (s7_314 IFM with PC...
Started by: SiemensAutoAnsari (July 28th, 2020)

July 31st, 2020 10:00 AM
by SiemensAutoAnsari

Anyone program this doohickey using controllogix. If so, how and maybe an example. My brain hurts...
Started by: davidhinch (July 31st, 2020)

July 31st, 2020 09:06 AM
by davidhinch

Good Day, I am unable to find any support using Powerflex 525 in multiple with other Powerflex...
Started by: righteous818 (July 29th, 2020)

July 31st, 2020 08:01 AM
by righteous818

Hello everyone, I'm using the trend of a PanelView800 to record data in a USB memory but I have...
Started by: marvis (July 30th, 2020)

July 31st, 2020 06:16 AM
by marvis

Hi, I am trying to home the Kinetix 300 drive using the home to sensor option, but for some...
Started by: msajid (July 29th, 2014)

July 31st, 2020 06:12 AM
by votecoffee

In a stand-alone application, what is wrong with the file creation failure? There is no problem...
Started by: huangshuai (July 30th, 2020)

July 31st, 2020 05:51 AM
by PreLC

I have a client that has iFix 5.8 installed with a Primary and secondary node. They have two...
Started by: CanIPLCit (July 30th, 2020)

July 31st, 2020 03:17 AM
by parky

150hp, 480v.
Started by: strantor (July 1st, 2020)

July 30th, 2020 10:11 PM
by Gene Bond

Hi peoples First post, be gentle (and helpful if you can) Been having a lot of fun with my...
Started by: mcummins (August 27th, 2008)

July 30th, 2020 07:45 PM
by jkerekes

Hi all, In need of some advice. Currently I am working on 2 new system projects about halfway...
Started by: bill4807 (October 18th, 2017)

July 30th, 2020 06:43 PM
by harryting

I'm troubleshooting a speed issue in Profibus right now. I can't remember the decimal value needed...
Started by: AutomationTechBrian (July 30th, 2020)

July 30th, 2020 05:50 PM
by Jobbe9000

I'm pretty sure the answer is no but I'll ask anyhow. I (we) use multistate indicators to display...
Started by: 77nomad (July 30th, 2020)

July 30th, 2020 04:13 PM
by I_Automation

I have a spec that requires cable redundancy whether or not it makes sense. Also, I have to have...
Started by: GlenOsborne (July 29th, 2020)

July 30th, 2020 02:09 PM
by GlenOsborne

Has anyone purchased from PLC-city.com before? I'm trying to determine if it's trustworthy or not....
Started by: Bunt23 (July 27th, 2020)

July 30th, 2020 12:37 PM
by geniusintraining

So I have copied the MER file from a panelview and converted to MED file. How to get updated tags...
Started by: MattMatt9 (July 29th, 2020)

July 30th, 2020 12:10 PM
by Clatchet