You are not registered yet. Please click here to register!


 
 
plc storereviewsdownloads
This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc.
 
Try our online PLC Simulator- FREE.  Click here now to try it.

---------->>>>>Get FREE PLC Programming Tips

New Here? Please read this important info!!!


Go Back   PLCS.net - Interactive Q & A > Search Forums

Showing results 1 to 8 of 8
Search took 0.01 seconds.
Search: Posts Made By: Thinkster
Forum: LIVE PLC Questions And Answers June 25th, 2014, 07:00 PM
Replies: 17
Views: 6,565
Posted By Thinkster
Also, make sure your running a 32-bit version of...

Also, make sure your running a 32-bit version of Windows 7. It works much better for us that use both 500 and 5000.
Forum: LIVE PLC Questions And Answers June 24th, 2014, 02:29 PM
Replies: 9
Views: 3,388
Posted By Thinkster
The serial Port server is a Digi PortServer TS4...

The serial Port server is a Digi PortServer TS4 MEI. And I believe the part number for the ProSoft card is the one I ordered.
Forum: LIVE PLC Questions And Answers June 23rd, 2014, 01:53 AM
Replies: 9
Views: 3,388
Posted By Thinkster
Just to clarify, I have serial modbus data going...

Just to clarify, I have serial modbus data going into a Digi Terminal Server which has RS232 Input and TCP/IP ethernet output. I can configure it for Industrial Automation mode. which supports...
Forum: LIVE PLC Questions And Answers June 19th, 2014, 10:38 AM
Replies: 9
Views: 3,388
Posted By Thinkster
How do I pull Modbus Data over Ethernet: CompactLogix

Without purchasing a prosoft card or similar, I would like to setup some message blocks to pull data from the ethernet port which is connected to a network switch that also has connected a Serial...
Forum: LIVE PLC Questions And Answers June 16th, 2014, 06:00 PM
Replies: 7
Views: 2,117
Posted By Thinkster
Really? This sounds like something I'd like to...

Really? This sounds like something I'd like to do. Each of the devices is the same model and will have the same registers (7001 - 7009) but obviously will have different Modbus slave addresses. So...
Forum: LIVE PLC Questions And Answers June 13th, 2014, 10:24 AM
Replies: 7
Views: 2,117
Posted By Thinkster
Got it. Was able to change settings on Total...

Got it. Was able to change settings on Total Flow to output the data in the correct order. Used one MSG command to pull the first 5 registers (7001 - 7010) and another MSG command for the next 3...
Forum: LIVE PLC Questions And Answers June 8th, 2014, 12:18 AM
Replies: 7
Views: 2,117
Posted By Thinkster
So I tinkered with the TotalFlow settings on the...

So I tinkered with the TotalFlow settings on the COMM port I designated for Modbus and I set the output type to 16Bit Word swapped. I then setup my 1st MSG to Read 7001 16Bit, 2 elements. Did same...
Forum: LIVE PLC Questions And Answers June 4th, 2014, 01:13 PM
Replies: 7
Views: 2,117
Posted By Thinkster
ABB TotalFlow Modbus to ML1100 help!

So I have an ABB TotalFlow uFlo G4 unit and have configured it's COMM port as Modbus Slave. I have also mapped internal 32Bit Float Registers to 7001 - 7009 locations using ABB's PCCU software. ...
Showing results 1 to 8 of 8

 
Forum Jump

All times are GMT -5. The time now is 12:52 AM.


.