You are not registered yet. Please click here to register!


 
 
plc storereviewsdownloads
This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc.
 
Try our online PLC Simulator- FREE.  Click here now to try it.

---------->>>>>Get FREE PLC Programming Tips

New Here? Please read this important info!!!


Go Back   PLCS.net - Interactive Q & A > Search Forums

Showing results 1 to 25 of 500
Search took 0.22 seconds.
Search: Posts Made By: jrwb4gbm
Forum: LIVE PLC Questions And Answers Today, 12:04 PM
Replies: 216
Views: 81,149
Posted By jrwb4gbm
Here you go. See attached. @gbradley, I just...

Here you go. See attached.
@gbradley,
I just didn't include all the options in the Report Options.
Forum: LIVE PLC Questions And Answers Yesterday, 04:42 PM
Replies: 4
Views: 144
Posted By jrwb4gbm
i think you are right, probably a faulty card....

i think you are right, probably a faulty card. Just pull it and look for any physical damage. If it looks alright, might as well try to substitute a known good card in its place. It might be a chip...
Forum: LIVE PLC Questions And Answers November 15th, 2017, 06:22 PM
Replies: 4
Views: 144
Posted By jrwb4gbm
Probably a dumb suggestion but are the minus (-)...

Probably a dumb suggestion but are the minus (-) terminals on all inputs connected back to the power source?
Forum: LIVE PLC Questions And Answers November 14th, 2017, 12:04 PM
Replies: 2
Views: 96
Posted By jrwb4gbm
See attached.

See attached.
Forum: LIVE PLC Questions And Answers November 14th, 2017, 11:57 AM
Replies: 2
Views: 71
Posted By jrwb4gbm
Here you go, see attached.

Here you go, see attached.
Forum: LIVE PLC Questions And Answers November 13th, 2017, 06:35 PM
Replies: 38
Views: 27,570
Posted By jrwb4gbm
Just upload the .acd file to a fileserver like...

Just upload the .acd file to a fileserver like tinyupload.com. Put the download link in a text file and zip the file with that link in it. Attach that file to a post. The resulting .pdf file will...
Forum: LIVE PLC Questions And Answers November 10th, 2017, 08:41 PM
Replies: 4
Views: 126
Posted By jrwb4gbm
I sent you a Private Message (PM) with a link....

I sent you a Private Message (PM) with a link. See near the top right side of the webpage for a button to access your PMs.
Forum: LIVE PLC Questions And Answers November 10th, 2017, 05:53 PM
Replies: 4
Views: 126
Posted By jrwb4gbm
Attached is an example of how to make a Timer...

Attached is an example of how to make a Timer Timing Output. If X0 is energized, Y0 will be on until the timer times out.
Forum: LIVE PLC Questions And Answers November 10th, 2017, 04:38 PM
Replies: 4
Views: 126
Posted By jrwb4gbm
I can help. Maybe I can find some links to the...

I can help. Maybe I can find some links to the manual you need. If not, I will upload the main manual to a fileserver and PM you a link that way. It's about 13 meg's in size though. If you would...
Forum: LIVE PLC Questions And Answers November 9th, 2017, 06:32 PM
Replies: 2
Views: 113
Posted By jrwb4gbm
Welcome to the Forum! See this link I found...

Welcome to the Forum!
See this link I found with Google. I have no idea if it will help.
http://www.judiwa.com/2011/02/02/how-to-setup-micrologix-sti-function/

Keep in mind there are some...
Forum: LIVE PLC Questions And Answers November 8th, 2017, 01:00 PM
Replies: 4
Views: 2,545
Posted By jrwb4gbm
Click on Downloads button above in the green bar,...

Click on Downloads button above in the green bar, then on the page that comes up, click on the Allen Bradley section. Plenty of examples available, just look thru them and get the parts you need.
...
Forum: LIVE PLC Questions And Answers November 6th, 2017, 03:58 PM
Replies: 13
Views: 762
Posted By jrwb4gbm
I vaguely do. Try Googling Automate or AutoMax or...

I vaguely do. Try Googling Automate or AutoMax or Reliance Electric PLC. As best I remember Allen Bradley or Rockwell bought that division from Reliance Electric or maybe not. It also resembles an...
Forum: LIVE PLC Questions And Answers November 2nd, 2017, 08:31 AM
Replies: 12
Views: 369
Posted By jrwb4gbm
I really don't know. See post #7. The plc2 was...

I really don't know. See post #7. The plc2 was sorta an earlier version of a plc5.
Forum: LIVE PLC Questions And Answers November 1st, 2017, 12:17 AM
Replies: 15
Views: 360
Posted By jrwb4gbm
Those two wires coiled up could be either a shunt...

Those two wires coiled up could be either a shunt trip connection that requires a power source or they could be simply connected to a small set of internal contacts that could be used by a plc input...
Forum: LIVE PLC Questions And Answers October 31st, 2017, 10:16 PM
Replies: 15
Views: 404
Posted By jrwb4gbm
I am not familiar with this particular drive but...

I am not familiar with this particular drive but I do know that as SCRs and other semi-conductor devices get older, they can become "leaky" at operating or elevated temperatures. They will test...
Forum: LIVE PLC Questions And Answers October 31st, 2017, 09:56 PM
Replies: 15
Views: 360
Posted By jrwb4gbm
If this panel has never been powered up, then,...

If this panel has never been powered up, then, the breaker "could" have tripped from any number of things. Most likely though, the panel was dropped or handled roughly during shipment. It may require...
Forum: LIVE PLC Questions And Answers October 31st, 2017, 09:32 PM
Replies: 15
Views: 360
Posted By jrwb4gbm
A breaker can fail in this position. That is the...

A breaker can fail in this position. That is the "Tripped" position.

I would recommend you get a fully qualified electrician to check it out!!.

If you must proceed, 1st, be sure to remove the...
Forum: LIVE PLC Questions And Answers October 30th, 2017, 09:35 PM
Replies: 12
Views: 369
Posted By jrwb4gbm
Please disregard the tinyupload.com link in the...

Please disregard the tinyupload.com link in the post #8 above. The pdf conversion was messed up and I have already Deleted the file in that link. If anyone wants a copy of the originally created...
Forum: LIVE PLC Questions And Answers October 30th, 2017, 06:18 PM
Replies: 12
Views: 369
Posted By jrwb4gbm
I sent a PM with a link to a rar'ed file of the...

I sent a PM with a link to a rar'ed file of the pdfs (projects) to afeefabdussamed. It was too big to post here. Here is that link if anyone would like to look at them.
Link:...
Forum: LIVE PLC Questions And Answers October 30th, 2017, 09:31 AM
Replies: 16
Views: 477
Posted By jrwb4gbm
Unless you need it to be Retentive you won't need...

Unless you need it to be Retentive you won't need counters. Just use the Done or output of the 1st timer to start a 2nd timer, etc. Use the output of the last timer to reset all after using it to...
Forum: LIVE PLC Questions And Answers October 30th, 2017, 09:18 AM
Replies: 16
Views: 477
Posted By jrwb4gbm
I'm only guessing since I am not familiar with...

I'm only guessing since I am not familiar with this software or plc. You may have already considered this. I would suggest just cascading some more timers using additional rungs in the logic unless...
Forum: LIVE PLC Questions And Answers October 30th, 2017, 09:03 AM
Replies: 12
Views: 369
Posted By jrwb4gbm
Unless you are actually trying to edit or make...

Unless you are actually trying to edit or make chnges in the program for an old PLC2, zip all the files in that project and attach them here in the thread. Maybe someone can open them for you and...
Forum: LIVE PLC Questions And Answers October 28th, 2017, 06:26 PM
Replies: 5
Views: 219
Posted By jrwb4gbm
The questions you were asking were very similar...

The questions you were asking were very similar to a classroom example. I have no training whatsoever in Siemens. If you think it will help, I can download the files I mentioned and print them to a...
Forum: LIVE PLC Questions And Answers October 28th, 2017, 06:04 PM
Replies: 5
Views: 219
Posted By jrwb4gbm
Steve Bailey has given you the best advice and...

Steve Bailey has given you the best advice and here is some additional info.
This info is not for the software/PLC that you are using. If you have access to RSLogixPro there are 4 files/examples of...
Forum: LIVE PLC Questions And Answers October 23rd, 2017, 04:37 PM
Replies: 13
Views: 601
Posted By jrwb4gbm
First of all, 69 is not old. I'm 74 and retired,...

First of all, 69 is not old. I'm 74 and retired, but still love PLCs and programming. I especially love the older plcs. You can learn plcs too. The main thing is don't get in too big of a hurry.
For...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 02:39 PM.


.