You are not registered yet. Please click here to register!


 
 
plc storereviewsdownloads
This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc.
 
Try our online PLC Simulator- FREE.  Click here now to try it.

---------->>>>>Get FREE PLC Programming Tips

New Here? Please read this important info!!!


Go Back   PLCS.net - Interactive Q & A > Search Forums

Showing results 1 to 25 of 27
Search took 0.01 seconds.
Search: Posts Made By: mhammer214
Forum: LIVE PLC Questions And Answers May 24th, 2018, 12:28 AM
Replies: 4
Views: 135
Posted By mhammer214
Check out the Turck TTM miniature sensors, they...

Check out the Turck TTM miniature sensors, they might be what you are looking for.
https://www.turck.de/en/sensors-1272_compact-temperature-sensors-1498.php
Forum: LIVE PLC Questions And Answers May 9th, 2018, 06:39 PM
Replies: 19
Views: 912
Posted By mhammer214
If you are stuck with the festoon wireway maybe...

If you are stuck with the festoon wireway maybe look into some tougher Ethernet cable. I am thinking for example something like Allen Bradley 1585 cable or possibly something along the lines of...
Forum: LIVE PLC Questions And Answers March 28th, 2018, 09:32 AM
Replies: 9
Views: 735
Posted By mhammer214
Had it been a conveyor for coal for example it...

Had it been a conveyor for coal for example it would have been more likely something like a 48" conveyor. :D
Forum: LIVE PLC Questions And Answers March 26th, 2018, 10:24 PM
Replies: 22
Views: 1,631
Posted By mhammer214
Without a load on the softstarter you will have...

Without a load on the softstarter you will have 480 volt on the output terminals because the thyristors always have a small leakage current. The internal resistance of a voltmeter is too high to pull...
Forum: LIVE PLC Questions And Answers February 19th, 2018, 01:06 PM
Replies: 26
Views: 1,094
Posted By mhammer214
I just had time to look at your application and...

I just had time to look at your application and noticed that you had used counter C5:0 in File 3 and in File 10. I was using Emulate500 and every time C5:0 reached 31 due to counting up in File 10,...
Forum: LIVE PLC Questions And Answers November 1st, 2017, 12:10 AM
Replies: 15
Views: 725
Posted By mhammer214
If you do not have any use for the UV trip I am...

If you do not have any use for the UV trip I am sure an experienced electrician would be able to remove it. This should be possible since you can get field mounted UV trip units for the Eaton N-frame...
Forum: LIVE PLC Questions And Answers October 31st, 2017, 11:49 PM
Replies: 15
Views: 725
Posted By mhammer214
Yes, something needs to supply power to the UV...

Yes, something needs to supply power to the UV trip unit in order for you to be able to reset and turn on the breaker. There might be a label next to where the wires enter the breaker that will tell...
Forum: LIVE PLC Questions And Answers October 31st, 2017, 10:58 PM
Replies: 15
Views: 725
Posted By mhammer214
+1 It looks like there are two wires going into...

+1
It looks like there are two wires going into the left side of the breaker. I think this breaker has an undervoltage trip unit which will trip the breaker when deenergized and you won't be able to...
Forum: LIVE PLC Questions And Answers October 12th, 2017, 12:07 PM
Replies: 10
Views: 707
Posted By mhammer214
This link has the manual for Modbus control of...

This link has the manual for Modbus control of the PXR temperature controllers including a Modbus address map:
http://www.skylarkcontrols.com/pdf_files/PXR_MODBUS_Protocol.pdf
Hope this helps
Forum: LIVE PLC Questions And Answers June 26th, 2017, 10:41 PM
Replies: 11
Views: 1,008
Posted By mhammer214
Ken, it could be a ground fault in the power...

Ken, it could be a ground fault in the power system. A ground fault in an isolated Delta system will drive the DC bus voltage up.
Forum: LIVE PLC Questions And Answers March 13th, 2017, 12:15 PM
Replies: 43
Views: 5,916
Posted By mhammer214
Also works with Excel

Also works with Excel
Forum: LIVE PLC Questions And Answers February 8th, 2017, 05:55 PM
Replies: 6
Views: 1,183
Posted By mhammer214
jraef, in the manual for the BGFL relay it states...

jraef, in the manual for the BGFL relay it states that it is for a grounded AC system, so I don't think it will work with the system that the OP is dealing with.
However I did see the the three...
Forum: LIVE PLC Questions And Answers February 8th, 2017, 05:41 PM
Replies: 8
Views: 1,057
Posted By mhammer214
I have used Rosemount 2088G transmitters before...

I have used Rosemount 2088G transmitters before which are gage psi transmitters, however they can be re-ranged to -14.7 psig which is 0 psia. I don't think that is possible with the Dwyer sensors you...
Forum: LIVE PLC Questions And Answers February 8th, 2017, 05:34 PM
Replies: 8
Views: 1,057
Posted By mhammer214
One thing to keep in mind is that the transducer...

One thing to keep in mind is that the transducer you are using is a gage transducer, not an absolute transducer, so it may not give you accurate readings when you get into the vacuum range.
Forum: LIVE PLC Questions And Answers February 8th, 2017, 01:33 PM
Replies: 6
Views: 1,183
Posted By mhammer214
Bender makes ground fault detectors, I do see...

Bender makes ground fault detectors, I do see them frequently on drill rigs and most of them have a horn and strobe connected.
Forum: LIVE PLC Questions And Answers February 4th, 2017, 06:55 PM
Replies: 8
Views: 1,229
Posted By mhammer214
Maybe an Advantech ADAM-6015 would work for you?

Maybe an Advantech ADAM-6015 would work for you?
Forum: LIVE PLC Questions And Answers January 29th, 2017, 02:47 PM
Replies: 3
Views: 992
Posted By mhammer214
It won't do it automatically unless you tell it...

It won't do it automatically unless you tell it to.
Take a look at the samples that are installed with your RSL5000 installation, on Windows 7 they are in C:\Users\Public\Documents\Studio...
Forum: LIVE PLC Questions And Answers January 13th, 2017, 03:27 PM
Replies: 8
Views: 1,411
Posted By mhammer214
From what I can tell by reading through some of...

From what I can tell by reading through some of the documentation on the SOLA website the size determines the range over which the power conditioner keeps the output voltage within 1%. It also...
Forum: LIVE PLC Questions And Answers January 12th, 2017, 01:43 PM
Replies: 8
Views: 1,411
Posted By mhammer214
Would something like a SOLA/HeviDuty CVS Series...

Would something like a SOLA/HeviDuty CVS Series Power Conditioner work? They make a 5 kva one that fits your voltage requrement. I have seen them used on the supply to PLCs.
Forum: LIVE PLC Questions And Answers September 27th, 2016, 01:08 PM
Replies: 4
Views: 1,297
Posted By mhammer214
I guess if your panel is firmware 3.011 or newer...

I guess if your panel is firmware 3.011 or newer then it does not have the browser interface anymore.
Did you follow the steps in the manual...
Forum: LIVE PLC Questions And Answers September 27th, 2016, 11:35 AM
Replies: 4
Views: 1,297
Posted By mhammer214
Connect to the IP address of the PanelView using...

Connect to the IP address of the PanelView using a web browser.
Forum: LIVE PLC Questions And Answers September 23rd, 2016, 12:07 PM
Replies: 4
Views: 717
Posted By mhammer214
According to the manual the maximum load on the...

According to the manual the maximum load on the 24 Volt control power supply (terminal 11) is 100 mA. I bet you are pulling down the 24 Volt to the point where you lose any of your inputs, hence the...
Forum: LIVE PLC Questions And Answers June 16th, 2016, 12:52 PM
Replies: 15
Views: 2,787
Posted By mhammer214
Page 327, Section 8.3, figure 8.1 is where I...

Page 327, Section 8.3, figure 8.1 is where I found the references to the RJ-45 connector in the above mentioned manual I was looking at.
Forum: LIVE PLC Questions And Answers June 16th, 2016, 12:49 PM
Replies: 15
Views: 2,787
Posted By mhammer214
I've been searching through the technical...

I've been searching through the technical reference manual MANUAL NO. SIEP C710606 18D from March 2014 and the only reference about the use I can find for the RJ-45 port is as a programming port...
Forum: LIVE PLC Questions And Answers April 25th, 2016, 09:44 AM
Replies: 4
Views: 509
Posted By mhammer214
I have seen CTs with built-in transducers that...

I have seen CTs with built-in transducers that convert the current to a 4-20 ma signal and I have also seen standalone transducers that take the standard 0-5 amps and convert it to a 4-20 ma signal....
Showing results 1 to 25 of 27

 
Forum Jump

All times are GMT -5. The time now is 06:37 AM.


.