Newbie looking for advice somashine basic - PLCS.net

Blake smith · July 20th, 2018, 05:36 AM

Hi all very new to plc programming all self taught to probably a lot of mistakes background I am a tunneling electrician mostly shot cret lining have a hald decent electrical back ground. I started programing with a plr schneiders zelio have designed and built a few panels useing zelio however I have started a project wich hopfully will broaden my plc knowledge I am using schneiders m221(TM221CE40T) PLC with a (tm3D116/G) digital expansion module and a (TMC2AQ2C) analog output cartridge programmed with so mashine basic and will also be using schneiders magelis HMIS5T touch screen programed with vijeo designer 6.2. All digital in/outs etc i have enough knowledge to comeplete this section of my project but I am coming unstuck when comes to analog inputs and out puts I have tried sourcing what info I can online YouTube etc other than schneiders own tutorials. i am struggling to grasp somashines software I know what I want to do if was using an arduino I could write the code but I'm not 2 things I'm trying to do 1 is use the analog output to control a 3 phase speed controller from the hmi rather than using a 10k pot so just need the 4mA to 20mA output to feed straight i to the controllers terminals and the 2nd thing I want to do is use a pnp proxy on a 4 prong pully mounted pic up to give a rpn read out on the hmi if could get a few pointers more on the plc side first then will have a go at setting the hmi up before I seek help if needed thanks in advance

Albert LaFrance · July 22nd, 2018, 11:39 AM

Hi Blake,

You might want to re-post your inquiry in the Live PLC Questions and Answers sub-forum, which is much more active. I'm sure you'll get some helpful responses. This Practice sub-forum is mostly used by people learning to use the forum software features.

Rockby · July 22nd, 2018, 12:44 PM

Using the card TMC2AQ2C SoMachine Basic gives you the option to scale the raw value (BCD) in a min. and max., type in you card part number in SoMachine Help and search. There is a description on how to scale the analog value.

July 20th, 2018, 05:36 AM	#1
Blake smith Member Join Date: Jul 2018 Location: Deal Posts: 7	Newbie looking for advice somashine basic Hi all very new to plc programming all self taught to probably a lot of mistakes background I am a tunneling electrician mostly shot cret lining have a hald decent electrical back ground. I started programing with a plr schneiders zelio have designed and built a few panels useing zelio however I have started a project wich hopfully will broaden my plc knowledge I am using schneiders m221(TM221CE40T) PLC with a (tm3D116/G) digital expansion module and a (TMC2AQ2C) analog output cartridge programmed with so mashine basic and will also be using schneiders magelis HMIS5T touch screen programed with vijeo designer 6.2. All digital in/outs etc i have enough knowledge to comeplete this section of my project but I am coming unstuck when comes to analog inputs and out puts I have tried sourcing what info I can online YouTube etc other than schneiders own tutorials. i am struggling to grasp somashines software I know what I want to do if was using an arduino I could write the code but I'm not 2 things I'm trying to do 1 is use the analog output to control a 3 phase speed controller from the hmi rather than using a 10k pot so just need the 4mA to 20mA output to feed straight i to the controllers terminals and the 2nd thing I want to do is use a pnp proxy on a 4 prong pully mounted pic up to give a rpn read out on the hmi if could get a few pointers more on the plc side first then will have a go at setting the hmi up before I seek help if needed thanks in advance

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Topics
Thread	Thread Starter	Forum	Replies	Last Post
Basic RSLogix help for a PLC newbie	Barneel	LIVE PLC Questions And Answers	6	August 8th, 2013 11:47 AM
1746 Bas Module (basic)	ravisashi	LIVE PLC Questions And Answers	6	January 21st, 2007 04:03 AM
GE Fanuc basic question, newbie	herman_swartz	LIVE PLC Questions And Answers	22	December 27th, 2005 08:15 AM
plc5 with AB 1771-DB basic module, its urgent plz help me	nileshsurya	LIVE PLC Questions And Answers	6	July 20th, 2005 01:45 AM
Converting C to basic	a.llex	LIVE PLC Questions And Answers	0	October 18th, 2004 02:30 PM



This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc.
*Try our online PLC Simulator- FREE. Click here now to try it.* ---------->>>>>Get FREE PLC Programming Tips

July 22nd, 2018, 11:39 AM	#2
Albert LaFrance Lifetime Supporting Member Join Date: Mar 2012 Location: Falls Church, VA Posts: 111	Hi Blake, You might want to re-post your inquiry in the Live PLC Questions and Answers sub-forum, which is much more active. I'm sure you'll get some helpful responses. This Practice sub-forum is mostly used by people learning to use the forum software features.

July 22nd, 2018, 12:44 PM	#3
Rockby Member Join Date: Jul 2015 Location: Houston Posts: 18	Using the card TMC2AQ2C SoMachine Basic gives you the option to scale the raw value (BCD) in a min. and max., type in you card part number in SoMachine Help and search. There is a description on how to scale the analog value.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)