Abb acs800 replace fan - PLCS.net

geoplc · April 21st, 2014, 07:25 AM

anyone KNOW THE MAINT CODE TO RESET THE "REPLACE FAN" HOURS RUN REGISTER IN ACS800 DRIVE. DID IT FEW YEARS BACK BUT CANT REMEMBER.

osmanmom · April 21st, 2014, 07:39 AM

01.44-16.12

geoplc · April 21st, 2014, 09:20 AM

Ok Im a little rusty. I know 1.44 is the fault code for the fan hour limit, but dont remember the significance of 16.12 and how I went about resetting it.

osmanmom · April 21st, 2014, 09:27 AM

Abc

geoplc · April 22nd, 2014, 09:10 AM

Sorry about delay, parameter 16.12 is not accessible on the keypad control, only goes to 16.11. I vaguely remember having to enter a pass code in order to do this. Supposedly it can be reset using drivewindow software which i believe we may still have. Will look into further.

osmanmom · April 22nd, 2014, 09:26 AM

Actually it depend your Firmware Manual User,

Inline,Crane,Fan Pump,Extruder,Traverse,IGBT all have their Firmware manual user.

The reset counter will different 16.11-16.12-16.09 base on Firmware manual.

i give you default ACS800 Standard Manual User,

the important thing your Manual User must keep at proper place

Cphe747 · September 30th, 2015, 08:44 AM

We have some ASC800 drives running on our plant. Some of them have recently gave Alarm Messages on the Control Panel which says: Replace Fan(4280)
I did replace the cooling fan with one from our spare drives.
My problem is the fact that Parameter 16.12 which is used to reset the cooling fan run time counter is not accessible on the control panel.
Is there any method to reset this counter either than using the PC Tool? Is there a pass key or anything that can enable me to view the Parameter 16.12 and 01.44 etc?

DickDV · September 30th, 2015, 05:42 PM

Why not give ABB Tech Service a call----800.752.0696 Option 1 and Option 1. Knowledgeable friendly people during business hours in Milwaukee WI and NO CHARGE!

Cphe747 · October 1st, 2015, 12:37 AM

Quote:

Originally Posted by DickDV

Why not give ABB Tech Service a call----800.752.0696 Option 1 and Option 1. Knowledgeable friendly people during business hours in Milwaukee WI and NO CHARGE!

I will do that, thank you very much

Wizlock · November 20th, 2015, 02:44 AM

Did you get anywhere on this? Having the same problem.

Cphe747 · November 20th, 2015, 03:10 AM

Quote:

Originally Posted by Wizlock

Did you get anywhere on this? Having the same problem.

Good day, unfortunately I did not come right. I have 20 of these drives. ABB South Africa says I have to send the drives to them or bring their technician onsite which is not practical.
Sorry

Milspecelectrician · May 26th, 2016, 08:58 AM

SOLUTION

Okay so I made this account JUST to reply and solve this problem for everyone...
To reset the fan counter do as follows

Go to parameter 16-03
-enter 2303 as passcode
-press enter
-"..." Should appear for a brief moment
Go to parameter 145 (yes 145 now exists, before it only went to 99)
-go to sub-parameter 13 Titled "FAN ON-TIME"
-Press enter
-now you must hold the down arrow until you have brought the hours down to zero. This will take some time as it only decreases in increments of 10, my counter is at 50 000+
-once back to zero press enter. Problem solved, drive should run immediately if being called on to start

Go to parameter 16-03 again
-Press enter
-enter 358 as passcode
-press enter

Now you are done. ACT button out and let fly!

Hope this helps everyone reading this in the future

Pete.S. · May 26th, 2016, 09:19 AM

Quote:

Originally Posted by Milspecelectrician

SOLUTION

Okay so I made this account JUST to reply and solve this problem for everyone...
To reset the fan counter do as follows

Go to parameter 16-03
-enter 2303 as passcode
-press enter
-"..." Should appear for a brief moment
Go to parameter 145 (yes 145 now exists, before it only went to 99)
-go to sub-parameter 13 Titled "FAN ON-TIME"
-Press enter
-now you must hold the down arrow until you have brought the hours down to zero. This will take some time as it only decreases in increments of 10, my counter is at 50 000+
-once back to zero press enter. Problem solved, drive should run immediately if being called on to start

Go to parameter 16-03 again
-Press enter
-enter 358 as passcode
-press enter

Now you are done. ACT button out and let fly!

Hope this helps everyone reading this in the future

That's awesome. Thanks for posting.

rupej · May 26th, 2016, 08:27 PM

Interesting- does the VFD actually prevent the drive from starting when the fan run-hours reach a certain limit? Or does it just alarm?

ranjankamath · June 16th, 2016, 12:00 PM

Thanks for your Post,can you please share ACS 800 Manual containing Parameter Description for Group 145

April 21st, 2014, 07:25 AM	#1
geoplc Member Join Date: Oct 2006 Location: PAinesville OH Posts: 123	Abb acs800 replace fan anyone KNOW THE MAINT CODE TO RESET THE "REPLACE FAN" HOURS RUN REGISTER IN ACS800 DRIVE. DID IT FEW YEARS BACK BUT CANT REMEMBER.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Topics
Thread	Thread Starter	Forum	Replies	Last Post
ABB ACS800 & Ethernet	Elcan	LIVE PLC Questions And Answers	5	May 20th, 2013 11:06 AM
ABB ACS800 Drive	Rob S.	LIVE PLC Questions And Answers	8	March 19th, 2013 06:00 PM
ABB RETA-01 to ACS800 firmware compatibility	Purrdie	LIVE PLC Questions And Answers	3	October 24th, 2011 11:02 PM
ABB ACS800 LC firmware	TOKG1Tech	LIVE PLC Questions And Answers	3	June 14th, 2011 09:13 PM
ABB ACS800 A1>min Fault (8110)	thebuzz	LIVE PLC Questions And Answers	9	May 14th, 2011 10:13 AM



This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc.
*Try our online PLC Simulator- FREE. Click here now to try it.*

April 21st, 2014, 07:39 AM	#2
osmanmom Member Join Date: Mar 2014 Location: JOHOR Posts: 1,455	01.44-16.12

April 21st, 2014, 09:20 AM	#3
geoplc Member Join Date: Oct 2006 Location: PAinesville OH Posts: 123	Ok Im a little rusty. I know 1.44 is the fault code for the fan hour limit, but dont remember the significance of 16.12 and how I went about resetting it.

April 22nd, 2014, 09:10 AM	#5
geoplc Member Join Date: Oct 2006 Location: PAinesville OH Posts: 123	Sorry about delay, parameter 16.12 is not accessible on the keypad control, only goes to 16.11. I vaguely remember having to enter a pass code in order to do this. Supposedly it can be reset using drivewindow software which i believe we may still have. Will look into further.

April 22nd, 2014, 09:26 AM	#6
osmanmom Member Join Date: Mar 2014 Location: JOHOR Posts: 1,455	Actually it depend your Firmware Manual User, Inline,Crane,Fan Pump,Extruder,Traverse,IGBT all have their Firmware manual user. The reset counter will different 16.11-16.12-16.09 base on Firmware manual. i give you default ACS800 Standard Manual User, the important thing your Manual User must keep at proper place

September 30th, 2015, 08:44 AM	#7
Cphe747 Member Join Date: Sep 2015 Location: Newcastle Posts: 4	We have some ASC800 drives running on our plant. Some of them have recently gave Alarm Messages on the Control Panel which says: Replace Fan(4280) I did replace the cooling fan with one from our spare drives. My problem is the fact that Parameter 16.12 which is used to reset the cooling fan run time counter is not accessible on the control panel. Is there any method to reset this counter either than using the PC Tool? Is there a pass key or anything that can enable me to view the Parameter 16.12 and 01.44 etc?

September 30th, 2015, 05:42 PM	#8
DickDV Member Join Date: May 2002 Location: Kalamazoo MI Posts: 2,324	Why not give ABB Tech Service a call----800.752.0696 Option 1 and Option 1. Knowledgeable friendly people during business hours in Milwaukee WI and NO CHARGE!

November 20th, 2015, 02:44 AM	#10
Wizlock Member Join Date: Aug 2014 Location: Western Norway Posts: 17	Did you get anywhere on this? Having the same problem.

May 26th, 2016, 08:58 AM	#12
Milspecelectrician Member Join Date: May 2016 Location: Canada Posts: 1	SOLUTION Okay so I made this account JUST to reply and solve this problem for everyone... To reset the fan counter do as follows Go to parameter 16-03 -enter 2303 as passcode -press enter -"..." Should appear for a brief moment Go to parameter 145 (yes 145 now exists, before it only went to 99) -go to sub-parameter 13 Titled "FAN ON-TIME" -Press enter -now you must hold the down arrow until you have brought the hours down to zero. This will take some time as it only decreases in increments of 10, my counter is at 50 000+ -once back to zero press enter. Problem solved, drive should run immediately if being called on to start Go to parameter 16-03 again -Press enter -enter 358 as passcode -press enter Now you are done. ACT button out and let fly! Hope this helps everyone reading this in the future

May 26th, 2016, 08:27 PM	#14
rupej Member Join Date: Sep 2014 Location: NC Posts: 938	Interesting- does the VFD actually prevent the drive from starting when the fan run-hours reach a certain limit? Or does it just alarm?

June 16th, 2016, 12:00 PM	#15
ranjankamath Member Join Date: Oct 2010 Location: Mysore Posts: 1	Thanks for your Post,can you please share ACS 800 Manual containing Parameter Description for Group 145

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)