HI. Where can I download a manual for Step7-micro/win?

I couldn't find the Step7 micro/win manual at the Siemens site. Is it free for downlaod and where can i get it, or I've to pay for it. There is a system manual for simatic 200, but not the micro/win manual.
Can you help me?
Best regards.

Try this... It's a "Manual Finder" (No, not a By-Hand Finder, but then... maybe it is!)

http://www4.ad.siemens.de/csinfo/li...nfo&objtype=9000&objAction=cshbprompt&lang=en

Then type in...

STEP-7 Micro/Win

...in the Search Term

I found the Micro/Dos only.

There is Step7 Micro/Dos only. I need the windows version. Any other ideas? I really need this manual.
Bye.

Step-7 Micro-Win Info

I had a difficult time finding these manuals (PDF-files) also. Maybe this link will help....

Step-7 Micro/Win 32
I'm not sure if this is the information you are looking for....

The 2 Manuals I have are:

1h_fib_kompl_e9907.pdf (5.25 MB) This is the S7-200 Starter Kit manual and.....

2h_fib_e_1299_komplett.pdf (1.92 MB) this one is the Micro System Simatic S7-200 (two hour primer).

Both of these files are too large to attach to this forum.

I may be able to E-Mail these to you if this is what you are seeking..

Thanx Dan

In another thread I had said that it is getting easier to navigate around the Siemens site... I lied... it seems to be getting worse... it's horrible!

What I did find was the following...

The manual for STEP 7 Micro/WIN, version 2.0, is only available in electronic form as a context-sensitive help system. Chapters 3 and 4("Getting Started") in the S7-200 System Manual have been revised according to the new version. Please order separately.

6ES7 810-2AA00-0YX0....STEP 7 Micro/WIN, single license

6ES7 810-2AA00-0YX1....STEP 7 Micro/WIN, copy license

6ES7 810-2AA00-0YX3....STEP 7 Micro/WIN, update

6ES7 298-8FA00-8.H0....S7-200 Reference Manual

6ES7 901-3BF00-0XA0....PC/PPI cable for S7-200

.


Good Luck

The Siemens site is so huge its easy to get lost or not find the area you need. Once you locate the support section usually you can find about anything.

As for the S7-200 and its software I thought they had a good page allocated to it:
http://www.sea.siemens.com/controls/prod_ref/CNpref12.htm

I am a little confused though, the manual for any siemens product is usually with the software, even my older version (which I can load anymore because disk 1 is bad) with 5 floppies had the instruction library etc. If you have a cd version is should definitely have an abundance of information. I am not sure about the Micro/Dos version, it is discontinued and not supported but you can obtain the Manual here:>http://www4.ad.siemens.de/dnl/DU1NTQyMQAA_1109255/Micro_e.pdf

The s7-200 Quick Reference card offers an abundance of info in a small package:http://www4.ad.siemens.de/dnl/TAyMTUxNQAA_2792346/S7200qrc_2ndgen_e.pdf

Alas the manual for the S7-200 has info on MicroWin and its use:
http://www4.ad.siemens.de/dnl/zc1NTE0NDcA_1109154/S7-200_e.pdf

I'm not sure that I've to pay for a PDF manual

I have the 1h primer and the 2h primer, but this is not what I need. The primers are almost useless. There is a manual especially for micro/win. I do not want to pay for a PDF file if its not free. Can you send me a copy of the micro/win manual on my mail. I have the demo CD, but there is no manual.
[email protected]
bye

If you are still looking for the MicroWin manual, send me a mail, I can help you!
Are you already working with V3.2?

Regards

[email protected]

I do not want to pay for a PDF file if its not free.

Click to expand...

Unfortunately, when things are not free you do have to pay for them!

Paul

HI. Where can I download a Step7-micro/win full version?
Omega Automation
Sheikhupura

Hello Muhammad;
Siemens offers a frre download DEmo version for MicroWin 4.0.
Here is how it is described in Siemens webpage:
This test version provides the full functionality of the normal product for 60 days. It can be started up to 100 times.

https://www.automation.siemens.com/...-200/demosoftware/microwin/Pages/Default.aspx

This should give you enough time to familisarize yourself with the software; eventually, you will have to think of purchasing the license:

6ES7810-2CC03-0YX3
STEP7-MICRO/WIN V4.0 (UG) G/E/F/I/S/C

The programming instructions for MicroWin are included in the S7-200 System manual, which you will find invaluable if you plan to work with these CPUs:
https://support.automation.siemens....arch&searchinprim=0&nodeid0=10805397&x=28&y=8

Hope this helps,
Daniel Chartier