Panleview 600 factory reset

Heloo.
Can someone help me how to factory reset PanelView 600. 2711-B6C1.
Thanks.

See page 153 in the manual:

http://literature.rockwellautomation.com/idc/groups/literature/documents/um/2711pc-um002_-en-p.pdf

To recover from a firmware update failure, for example, fatal code 0F, you need to
restore your terminal to its out-of-box, factory default state.
Follow these steps to restore factory defaults from Maintenance mode.
1. Press and hold the DEFAULT switch on the back of the logic module.
2. Press and release the RESET switch.
3. Release the DEFAULT switch.
The maintenance menu is displayed.
Maintenance Window with Safe Mode Selected
default button pressed, please select maintenance options
Maintenance Menu -- ver 0x.xx
Special BOOT Action - SAFE Mode
Reboot with selected options Selects the special BOOT
action that will be
executed during this system
boot.
- SAFE mode-------------------------
The system will start in the
configuration mode of
FactoryTalk View ME Station.
- IMPORTANT-------------------------
FactoryTalk View ME Station
will load at start up not
the custom HMI application.
The HMI application will
start normally the next
time the terminal is rebooted.
The version refers to the
boot loader.
TIP Terminals require an attached USB keyboard to navigate in Maintenance mode.
154 Rockwell Automation Publication 2711PC-UM002C-EN-P - March 2015
Chapter 8 Troubleshooting
4. Press the down arrow on the keyboard to select the following option:
Special BOOT Action -None
5. Press the right arrow three times to select the following option:
Special BOOT Action - Restore Factory Defaults
6. Press the up arrow to select ‘Reboot with selected options’.
7. Press Enter on your keyboard to initiate the factory default restore process.
The terminal is returned to its out-of-box state, including the firmware,
registry, file system, and storage areas. All user data is lost after the restore.

I dont have any default switch on the back of the PV600 unit. No key, no switch, no button on the back!

This is not a PLUS version. This is the plain PV600

For a PanelView 600. 2711-B6C1 ( Standard PanelView) See text

But all you need to do is load a new program, it will write over the old.

Thanks Mickey. It looks like it worked.
This is the RIO module, we talked about it few weeks ago.
I ordered a RIO scanner card. I managed the scanner card to go OFF the fault, but never
was able to run it. Now iam trying to do that.
Bought a 2Gb memory card, did not work. I just want to have it up at least to communicate with it...
On the PV 600 now I have the fault flashing.

Sorry about that, I did a search on Rockwell for PV600 and didn't notice the manual that came up was for the PV+

No problem, I appreciate your willingness to help.
I managed now to reset, but the red Fault LED is flashing.
What now? it is the RIO version. Cable connected. Need to address it properly...
I guess. ANy help is welcome.
Thanks

Have you tried to connect to the RS232 port using RSLinx. And load a new program

Straight thru cable. DF1 driver?

I did not. It is a printer driver.
Should I?

The RS232 is a printer port.

Its also a AUX upload/download port, that's its default setup.

See picture

Default settings

FYI, I have not setup a RIO PV.

I just made a little program in Panelbuilder32.
Onl;y one maintained push button.
Now the settings: PV600/RIO/ Aux portownload
PLC ype: SLC504.../Name:542/ Rack 0/ Module: 0,2/ Last chassis (check)
In block transfer: should I have anything enabled? If yes: is R or W, length?
Pass though should be checked?