You are not registered yet. Please click here to register!


 
 
plc storereviewsdownloads
This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc.
 
Try our online PLC Simulator- FREE.  Click here now to try it.

---------->>>>>Get FREE PLC Programming Tips

New Here? Please read this important info!!!


Go Back   PLCS.net - Interactive Q & A > PLCS.net - Interactive Q & A > LIVE PLC Questions And Answers

PLC training tools sale

Reply
 
Thread Tools Display Modes
Old February 17th, 2017, 08:09 AM   #1
catalinoac
Member
Philippines

catalinoac is offline
 
Join Date: Feb 2013
Location: Cebu
Posts: 3
Door simulation lower limit switch (ls2) wiring configuration

  • The original limit switch wiring configuration on Door Simulation are
    LS1 = N.O.
    LS2 = N.O.

    Upon reading on the exercise, there is a "For Discussion" in which the
    the LS2 (lower) may be rewired to N.C. for "fail safe design" operation.
    <u>

  • Upper Limit switch wired N.O., Lower limit switch rewired N.C. resulting in:
    Upper limit switch (door open) goes False(0) when Door reaches the fully open position.
    Lower limit switch (door closed) goes False(0) when door reaches the fully closed position.
Task> Explain why this last rewiring option should result in a safer, more fault tolerant installation.
  • </u>With the wiring configuration of LS2 change from N.O. to N.C. would result in a fail-safe (OPEN CIRCUIT) protection. (As the motor will not run down if the circuit on limit switch is open)

    My question is, how about "SHORT CIRCUIT"? If LS2 will be shorted, then motor will run down (when PB closed is pressed) and will NOT STOP down to LS2 (as LS2 is shorted)
Please enlighten. Thanks

  Reply With Quote
Old February 17th, 2017, 08:22 AM   #2
Mispeld
Member
United States

Mispeld is offline
 
Join Date: Feb 2017
Location: VA
Posts: 67
The task asks why the configuration is "more fault tolerant." Focus on the failure modes handled by one N.O. and one N.C. switch.
Your question is valid and goes down the path of performance levels in safety designs. There are devices on the market which can detect shorted wiring and faulty devices, but are more complicated and expensive than basic limit switches.
  Reply With Quote
Old February 17th, 2017, 08:28 AM   #3
gclshortt
Member
Canada

gclshortt is offline
 
gclshortt's Avatar
 
Join Date: Dec 2014
Location: Cobourg
Posts: 1,723
https://www.allaboutcircuits.com/tex...l-safe-design/

http://www.plctalk.net/qanda/showthread.php?t=2224

The above information should help you out. The top link will also discuss "Short Circuits".
We now have "Safety Relays" that will prevent all errors on the circuit.
http://www.plctalk.net/qanda/archive...p/t-79059.html

Hope this helps you out.
Regards,
__________________
Garry
http://www.accautomation.ca
  Reply With Quote
Old February 17th, 2017, 08:42 AM   #4
catalinoac
Member
Philippines

catalinoac is offline
 
Join Date: Feb 2013
Location: Cebu
Posts: 3
Thanks you so much guys. Much appreciated.
  Reply With Quote
Reply
Jump to Live PLC Question and Answer Forum

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Topics
Thread Thread Starter Forum Replies Last Post
Problem with BTW & BTR in PLC-5 Gsquare LIVE PLC Questions And Answers 38 January 26th, 2015 06:45 AM
PLC5 Rack As RIO For ControlLogix tgoulding LIVE PLC Questions And Answers 38 May 17th, 2011 03:55 PM
Pls help sree46 LIVE PLC Questions And Answers 2 December 13th, 2009 07:36 AM
Mitsubishi PLC : CC-Link Wiring Configuration zai_jnr LIVE PLC Questions And Answers 7 December 18th, 2008 01:23 PM
AB 1770-KF2 module- Half duplex configuration ranjana LIVE PLC Questions And Answers 11 October 3rd, 2002 12:35 AM


All times are GMT -5. The time now is 04:30 AM.


.