SLC 5/04 - HSCE2 problems - processor fault

Robotroc

Member
R
Join Date
Sep 2011
Location
Bucharest
Posts
46
Hy guys,

I think i have a little problem with my old HSCE2 module for SLC 5/04 processor. Well ... i can't acces the M0 file from module !! Does anybody knows how ? I what to configure my module like this: ring count, X4 quad,operating mode 1, and other M0 setings. The problem is: When i press the I/O module config. and i select the M0 lenght .. so i whant to put 4 or 3 or even 1, when i go online, my processor goe's to fault and say something that's a problem with my HSCE2 module memory. When i put 0 ( zero ) to M0 lenght work's fine but i can't acces the M0 words and i can't configure my module to count as i want.

Thank you very much

Have a nice day !
 
Robotroc said:
Hy guys,

I think i have a little problem with my old HSCE2 module for SLC 5/04 processor. Well ... i can't acces the M0 file from module !! Does anybody knows how ? I what to configure my module like this: ring count, X4 quad,operating mode 1, and other M0 setings. The problem is: When i press the I/O module config. and i select the M0 lenght .. so i whant to put 4 or 3 or even 1, when i go online, my processor goe's to fault and say something that's a problem with my HSCE2 module memory. When i put 0 ( zero ) to M0 lenght work's fine but i can't acces the M0 words and i can't configure my module to count as i want.


Thank you very much

Have a nice day !
Click to expand...


The HSCE2 Class 4 CONFIGURE button from i/o config. isn't active ! why ? :(..
 
I just finished one of these things yesterday. Mine was linear, not ring, but I'm sure its something small. Are you using a load routine to for the card parameters, or just doing it in the output table ?
 
Earthscape said:
I just finished one of these things yesterday. Mine was linear, not ring, but I'm sure its something small. Are you using a load routine to for the card parameters, or just doing it in the output table ?
Click to expand...

I don't know how to config. it because i can't acces the M0 file. Can u send me your project pls ( only encoder setup )?

The error is : "Slot 1 has a M0-M1 file configuration error - user program M0-M1 file size exceeds capacity of the module."

thank's
 
Last edited:
- Here you go, I used example 2 for a Class 4, Mode 1 encoder for initialization. I edited the table for a linear encoder, not ring.

I reset the encoders with a MVM from the HMI.

XIC B3:1/0 OSR B3:1/1 MVM N16:0 0002H #O:30.1

XIO B3:1/0 OSR B3:1/2 MVM N16:1 0002H #O:30.1

Data Table.jpg
 

Similar Topics

R
SLC 500 Totalizer HSCE2 Module
I have a SLC5/03 that is using a HSCE2 High Speed Counter module. I have 3 pulse flowmeters hooked to the module. I need to totalize each flow...
Replies
2
Views
4,868
Ken Moore
Ken Moore
J
Sending temperature from SLC-5/02 to EZiMarquee
I’m attempting to send a temperature from a SLC-5/02 to an EZiMarquee display. The vendor said to use a MSG instruction to send the data to the...
Replies
1
Views
43
dmroeder
dmroeder
M
SLC 505 Outputs not firing
Hello all. I have a few SLCs in my plant and of late we've seen a weird issue: The system will be running normally and then randomly the outputs...
Replies
2
Views
62
Mark_J
M
I
Prosoft Datalogger w/ DF1 Comms to SLC 5/05 - Testing with MicroLogix
I am working on setting up a Prosoft Datalogger model PLX51-DLplus-232. This unit will be collecting data from a SLC 5/05 on the DB9 port set to...
Replies
3
Views
93
Ken Roach
Ken Roach
A
SLC messaging with a ControlLogix redundant system
I have a redundant ControlLogix being set up. This program reads a value from a remote site which happens to be SLC PLC. Rockwell mentions SLC...
Replies
2
Views
91
robertmee
R
Back
Top Bottom