Series 90-30 GE ,Error 8036

Hi Every one,

while PLC program uploading Ge fanuc CPU 90-30 CPU 313 having built in cpu 5 slots rack mounted and module ic693apu301 is attached with it , getting this error code.

dont know what exactly error is.
IC693APU301 picture is attached

Indication of module:
EN1 ON
EN2 OFF
stat ON
ok ON
cfg ON

Uploading from the connected device
Error 8036: Address '%AQ0002' on 'AQ0002[0]' is already used on 'AQ0001[1]'
Error 8036: Address '%AQ0003' on 'AQ0002[1]' is already used on 'AQ0001[2]'
Warning 8022: Type mismatch between variable and instruction. [LD Block,'ALLARMI': Rung 19]
Uploading: CONFIG VERSION
Uploading: REF MEMORY ALLOC
Uploading: RACK SLOT CONFIG
Uploading: I/O CONFIG
Uploading: SNP ID
Uploading: _MAIN.dec
Uploading: _MAIN.pdt
Uploading: COMBIT.pdt
Uploading: COMWORD.pdt
Uploading: PROFACE.pdt
Uploading: ALLARMI.pdt
Uploading: SINCRO.pdt
Uploading: Values - %R
Uploading: Values - %AI
Uploading: Values - %AQ
Uploading: Values - %G
Uploading: Values - %M
Uploading: Values - %Q
Uploading: Values - %I
_MAIN.pdt Processed successfully.
COMBIT.pdt Processed successfully.
COMWORD.pdt Processed successfully.
PROFACE.pdt Processed successfully.
ALLARMI.pdt Processed successfully.
SINCRO.pdt Processed successfully.
Building block: _MAIN....
Size of Logic Binary File = 165 Bytes
Successfully processed.
Building block: COMBIT....
Size of Logic Binary File = 168 Bytes
Successfully processed.
Building block: COMWORD....
Size of Logic Binary File = 249 Bytes
Successfully processed.
Building block: PROFACE....
Size of Logic Binary File = 202 Bytes
Successfully processed.
Building block: ALLARMI....
Size of Logic Binary File = 297 Bytes
Successfully processed.
Building block: SINCRO....
Size of Logic Binary File = 362 Bytes
Successfully processed.
---------- Post Processing ----------
%R Initial Values
%AI Initial Values
%AQ Initial Values
%G Initial Values
%M Initial Values
%Q Initial Values
%I Initial Values
---------- Upload from Controller completed ----------
Preparing target for import
Importing Hardware Configuration...
Importing Folder File...
Importing Smart Store...
Importing Variable File...
Importing block ALLARMI...
Importing block COMBIT...
Importing block COMWORD...
Importing block PROFACE...
Importing block SINCRO...
Importing block _MAIN...
The selected memory was successfully uploaded from the connected device.


Please Expert your opinion and expertise required thanks in advance.

It looks like %AQ1 & 3 are configured as DINT most likely in the APU but %AQ2 & 3 are also referenced and/or used in logic. If the program has been running properly ignore this and set Prophecy ME to ignore it also.
The photo looks like you need a new RAM backup battery, so don't turn off power to this unit until it is changed or you could lose the program and register data.

Ic693apu301

Hi Russ,

Thanks for your expert opinion. i set controller duplicate address as ignore,when i go online and try to upload program target is not equal,i check rack cpu and module numbers position still program is not equal,

Picture and program is attached.

I am using machine edition 8.5 version.

1) i am bit confused why my program is not equal with actual????
2)do i require for APM Vmware???

what i get in from feed back zone is:

Uploading from the connected device
Warning 8022: Type mismatch between variable and instruction. [LD Block,'ALLARMI': Rung 19]
Uploading: CONFIG VERSION
Uploading: REF MEMORY ALLOC
Uploading: RACK SLOT CONFIG
Uploading: I/O CONFIG
Uploading: SNP ID
Uploading: _MAIN.dec
Uploading: _MAIN.pdt
Uploading: COMBIT.pdt
Uploading: COMWORD.pdt
Uploading: PROFACE.pdt
Uploading: ALLARMI.pdt
Uploading: SINCRO.pdt
Uploading: Values - %R
Uploading: Values - %AI
Uploading: Values - %AQ
Uploading: Values - %G
Uploading: Values - %M
Uploading: Values - %Q
Uploading: Values - %I
_MAIN.pdt Processed successfully.
COMBIT.pdt Processed successfully.
COMWORD.pdt Processed successfully.
PROFACE.pdt Processed successfully.
ALLARMI.pdt Processed successfully.
SINCRO.pdt Processed successfully.
Building block: _MAIN....
Size of Logic Binary File = 165 Bytes
Successfully processed.
Building block: COMBIT....
Size of Logic Binary File = 168 Bytes
Successfully processed.
Building block: COMWORD....
Size of Logic Binary File = 249 Bytes
Successfully processed.
Building block: PROFACE....
Size of Logic Binary File = 202 Bytes
Successfully processed.
Building block: ALLARMI....
Size of Logic Binary File = 297 Bytes
Successfully processed.
Building block: SINCRO....
Size of Logic Binary File = 362 Bytes
Successfully processed.
---------- Post Processing ----------
%R Initial Values
%AI Initial Values
Variable _%AI0005 has been created
Variable _%AI0013 has been created
Variable _%AI0014 has been created
%AQ Initial Values
%G Initial Values
%M Initial Values
%Q Initial Values
%I Initial Values
---------- Upload from Controller completed ----------
Preparing target for import
Importing Hardware Configuration...
Importing Folder File...
Importing Smart Store...
Importing Variable File...
Importing block ALLARMI...
Importing block COMBIT...
Importing block COMWORD...
Importing block PROFACE...
Importing block SINCRO...
Importing block _MAIN...
The selected memory was successfully uploaded from the connected device

Please Experts help required.

Thanks in advance..

There may be a stored motion program in the APU301 module and that might be the reason for the configuration inequality.
Select the module in the navigator, press F1 for module-specific help and then go to the selection "Integration of the APM Motion Programmer to Machine Edition" for details about how to retrieve the stored program.

This certainly is an unusual configuration with only a "Follower Axis" and the Mater set to max speed of "0".
You will find more information on this at the GE Web Site, here:
https://ge-ip.force.com/communities/CC_Knowledge?q=ic693APU301