      |
||
 |
||
    This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc. |
||
 Try our online
PLC Simulator- FREE.
Click here now to try it.
| ||
New Here? Please read this important info!!!
December 2nd, 2019, 01:54 PM
|
#1 |
|
Member
 
Join Date: Oct 2018
Location: Leesville
Posts: 81
|
ABB ACS550 Earth Fault
I just replaced this drive as the old one went out when the plant had a power surge/flicker.
1-Installed the drive 2-Powered up 3- Got an immediate EARTH FAULT, so I check the manual and it talks about wires being grounded. 4- Disconnected wires from the motor and ohm out the wires to ground( CHECKS GOOD) 5-So I ohmed out the motor and I was getting 40-50 ohms when tested to ground.  6-I have not powered up the drive with out the wires disconnected. I will try that next to confirm my thoughts that the motor windings are starting to go bad and current is leaking out. Bad motor? |
|
|
December 2nd, 2019, 02:06 PM
|
#2 | |
|
Lifetime Supporting Member
Join Date: Mar 2005
Location: ENE of Nowhere Oklahoma
Posts: 10,602
|
Quote:
__________________
You can choose a ready guide in some celestial voice. If you choose not to decide you still have made a choice. |
|
|
|
|
December 2nd, 2019, 02:49 PM
|
#3 |
|
Member
Join Date: Oct 2018
Location: Leesville
Posts: 81
|
Seperated motor from power booted drive up and no fault. looks like im searching for a motor. Thanks OkiePc
|
|
|
|
December 2nd, 2019, 08:38 PM
|
#4 |
|
Member
Join Date: May 2006
Location: Northern California
Posts: 1,950
|
VFDs are better at finding faults than a lot of other things that are supposed to...
|
|
|
|
December 3rd, 2019, 08:02 AM
|
#5 | |
|
Lifetime Supporting Member
Join Date: Mar 2005
Location: ENE of Nowhere Oklahoma
Posts: 10,602
|
Quote:
 That should read 10 megohms. I have seen motors on starters work as low as 2 Mohm. I once replaced an obsolete 1336 VFD with a Toshiba G7 and it wouldn't run. The motor megger test showed 80 Megohms to ground... The 1336 was fine with it, the G7 said nope.
__________________
You can choose a ready guide in some celestial voice. If you choose not to decide you still have made a choice. |
|
|
|
 |
| Bookmarks |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
|
Similar Topics
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Abb acs550 pfc macro control | osama223 | LIVE PLC Questions And Answers | 2 | August 1st, 2017 10:51 AM |
| ABB AC drive fault | mmgch | LIVE PLC Questions And Answers | 3 | August 7th, 2009 04:48 AM |
| Generic fault finding methodology | Engineer1 | LIVE PLC Questions And Answers | 7 | July 16th, 2009 08:36 PM |
| RSLogix User Fault Routine | jthornton | LIVE PLC Questions And Answers | 17 | October 23rd, 2008 03:55 PM |
| Mitsubishi Still Sucks... | Eric Nelson | LIVE PLC Questions And Answers | 23 | January 15th, 2003 05:15 PM |
You are not registered yet. Please click here to register!
Linear Mode
