slc 5/04 DH 485 network problem - PLCS.net

MarkM · September 4th, 2003, 06:51 PM

I built a trainer with a 5/01, 1747-AIC, 1 quartech 9601 PB/SS station and a 9701 message display. I connect with a 1747-PIC. This network works fine.
Now I was able to pickup a 5/04 with a 1761-net-AIC and a homemade 1747-CP3 cable. With the old setup in linx I can see all four devices on the network. But with the new setup I only see the PC and the SLC. The other two devices have a red X through them. The nodes are the same on both networks. The PC is 0, the SLC is 1, the 9601 is 2 and the 9701 is 3.
I changed ch. 0 to DH485 and run with the pic driver. Both quartech devices are DH485. I connect the PC to net-AIC port #1 with the 1747-CP3. Port #2 goes to the SLC using a 1761-CBL-PM02. And #3 connects the DH485 from the old AIC to the net-AIC DH485. I've checked the archive and the AB site. I've been working on this for a couple of days, I know I'm missing something.

Mark

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Topics
Thread	Thread Starter	Forum	Replies	Last Post
read-write thru dh 485	labingtone	LIVE PLC Questions And Answers	1	September 20th, 2004 07:38 AM
DH 485 network	ttran	LIVE PLC Questions And Answers	1	June 1st, 2004 10:20 AM
slc 5/04 communication problem	tobias	LIVE PLC Questions And Answers	1	May 25th, 2004 01:08 AM
Communication between PanelView 1000 and SLC 5/04	RP	LIVE PLC Questions And Answers	50	December 9th, 2003 12:50 PM
DH 485 network	Jezz	LIVE PLC Questions And Answers	1	April 9th, 2003 07:33 AM



This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc.
*Try our online PLC Simulator- FREE. Click here now to try it.* ---------->>>>>Get FREE PLC Programming Tips

September 4th, 2003, 06:51 PM	#1
MarkM Member Join Date: Aug 2003 Posts: 1	slc 5/04 DH 485 network problem I built a trainer with a 5/01, 1747-AIC, 1 quartech 9601 PB/SS station and a 9701 message display. I connect with a 1747-PIC. This network works fine. Now I was able to pickup a 5/04 with a 1761-net-AIC and a homemade 1747-CP3 cable. With the old setup in linx I can see all four devices on the network. But with the new setup I only see the PC and the SLC. The other two devices have a red X through them. The nodes are the same on both networks. The PC is 0, the SLC is 1, the 9601 is 2 and the 9701 is 3. I changed ch. 0 to DH485 and run with the pic driver. Both quartech devices are DH485. I connect the PC to net-AIC port #1 with the 1747-CP3. Port #2 goes to the SLC using a 1761-CBL-PM02. And #3 connects the DH485 from the old AIC to the net-AIC DH485. I've checked the archive and the AB site. I've been working on this for a couple of days, I know I'm missing something. Mark

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)