aufisherman, Bullzi, cavedog, ChipMaker, el greco, ElectroRazr, g.mccormick, gbradley, jimtech67, Jkoso, JMP0, kamenges, kotr, Leukic, MHennel, mylespetro, nraj619, Peter Nachtwey, ScottTheEngineer, sigmadelta, Steve Bailey, Tim Hodges, Toine, VallejoWW

plcman2, JesperMP, Eric Nelson, MarkNightingale, jgreenewv, Steve Bailey, Ken Roach, Steve Etter, boneless, dcooper33, bernie_carlton, gmferg, Christoff84, JeffKiper, sthompson, kolyur, daba, iant, geniusintraining, nettogrisen, RheinhardtP, jrwb4gbm, TheWaterboy 

Hi All, with Phil Melore's (Site creator) approval, we have created a PLCS.net LinkedIN page for...
Started by: RheinhardtP (October 23rd, 2016)

May 16th, 2019 08:56 PM
by najma

I am trying to add datalinks to a couple of PF525 drives in studio 5000 V31 in order to use the...
Started by: jakeparsons03 (June 24th, 2019)

Yesterday 06:58 PM
by rupej

I'm having an issue connecting to a SCADAPack 357 over Ethernet for programming. I can connect...
Started by: PeterW (June 25th, 2019)

Yesterday 05:01 PM
by Bullzi

What is the difference between the Index+/- signals and the ABS signal shown in the pinout of the...
Started by: Archie (June 25th, 2019)

Yesterday 03:00 PM
by kamenges

Hi, I am having an application in which we are having a Roller rotating via Powerflex 527 drive....
Started by: gzPLC (June 14th, 2019)

Yesterday 02:34 PM
by gzPLC

To make a long story short, my customer has a Panelview that had an application already running in...
Started by: A_G (May 6th, 2019)

Yesterday 02:12 PM
by A_G

Hi all, i have a module from b&r automation and i am want to get the data from it, but the com...
Started by: Lithium3d (June 25th, 2019)

Yesterday 01:55 PM
by Lare

Hi, It's been a while since I've been doing PLC work as I've been concentrating on a large...
Started by: Jonnie_R (February 1st, 2015)

Yesterday 01:14 PM
by satnam_singh

My Panelview Plus 7 Performance with firmware v10 gave me this error message: "Error #2: terminal...
Started by: A_G (June 25th, 2019)

Yesterday 12:55 PM
by Ken Roach

I have two output cards sitting next to each other in a rack: 1746-OW16 1746-OW16 (Octal) ...
Started by: Russ (June 25th, 2019)

Yesterday 12:35 PM
by James Mcquade

Hello, Having a problem I have not encountered before. This is an existing set up that has been...
Started by: FourFront (June 25th, 2019)

Yesterday 11:53 AM
by FourFront

Hi, Can anyone else try this and tell me what revision you are using if the value is correct. ...
Started by: JeremyAdair87 (June 24th, 2019)

Yesterday 10:57 AM
by jimtech67

We have a compact logix L32E running RsLogix 5000 v.20, connected to two panelview plus 6 1000 over...
Started by: martinzstl (June 24th, 2019)

Yesterday 09:56 AM
by martinzstl

Hi. I can usually change the source value on these mov instructions but here in this particular one...
Started by: showshocka (June 19th, 2019)

Yesterday 08:35 AM
by jstolaruk

Hello! Guys! I finally solved the problem of convert S5 to S7 ! Really thank you for your advice!...
Started by: Bandy (June 24th, 2019)

Yesterday 08:30 AM
by Manglemender

How many device can be connected by using RS_232? I know that there will be only one RS-232...
Started by: karthiknd7 (June 20th, 2019)

Yesterday 08:20 AM
by shooter

Hello again!!! I have an interesting problem in our Boilerhouse control system...almost every...
Started by: David_Emmerich (June 25th, 2019)

Yesterday 08:11 AM
by Manglemender

Has anyone worked with Miyachi laser welder ? I am having some issues when selecting I/O job...
Started by: RogerF089 (June 25th, 2019)

Yesterday 07:07 AM
by RogerF089

Hello again~ I have a question in S5 51360 51361 51362 When Converting it, There was an...
Started by: Bandy (June 24th, 2019)

Yesterday 06:22 AM
by parky

Chaps, I have an Omron NQ5-SQ000-B HMI, and I need to back up the application, firmware and...
Started by: bigvern10 (June 24th, 2019)

Yesterday 02:42 AM
by bigvern10

I am looking for a way to capture keyboard input data and store it in a tag. Something like...
Started by: jme (June 24th, 2019)

June 24th, 2019 10:41 PM
by jme

All, I know this type of question has been asked (and sometimes answered) ad infinitum but after...
Started by: jkelleyus (June 20th, 2019)

June 24th, 2019 08:00 PM
by damica1

New user here with an 252h fault code. I've tried clearing the fault but it's persistent. Trying to...
Started by: Spencer.hall (June 24th, 2019)

June 24th, 2019 07:47 PM
by Ken Roach

Hi all, I am connecting direct from PC to PLC, which has a 5563 processor (NO Ethernet Port). I...
Started by: duckman (June 23rd, 2019)

June 24th, 2019 06:56 PM
by duckman

Tonight I'm contemplating using a technique I saw the other day while troubleshooting an...
Started by: AutomationTechBrian (June 21st, 2019)

June 24th, 2019 06:13 PM
by AutomationTechBrian

So I was commissioning this small pump house. Actually, the one from my old post. It was about 6PM...
Started by: sparkie (June 14th, 2019)

June 24th, 2019 06:10 PM
by OkiePC