Eric Nelson
Lifetime Supporting Member + Moderator
jBetts said:
I highly doubt it. Although, there's a good chance you could destroy the COM port on the Micro and/or your PC... :nodi:
You need a converter, period.
beerchug
-Eric
Idec Micro-1 Data cable pinout required
- Thread starter John Cairns
- Start date
I highly doubt it. Although, there's a good chance you could destroy the COM port on the Micro and/or your PC... :nodi:
You need a converter, period.
beerchug
-Eric
glenncovington
Lifetime Supporting Member
Here is a source for the cable you need.
http://www.plc-support.com/IDECMicro1.htm
It is $44.98 + Shipping
http://www.plc-support.com/IDECMicro1.htm
It is $44.98 + Shipping
junnel
Member
guys,
thus anyone have a copy of schematic diagram for the said idec micro-1 converter? or may be an interface cable if any?
regards,
junnel
thus anyone have a copy of schematic diagram for the said idec micro-1 converter? or may be an interface cable if any?
regards,
junnel
junnel
Member
good day!
Ive been working with microsmart plc and its working good. now, winldr software have the option for micro-1 plc but I dont have the cable, is there a way I can do to have my micro plc working as well? or do you have an idea of an adaptor or something i could match with the existing cable I am working with in order to access micro-1?
Ive been working with microsmart plc and its working good. now, winldr software have the option for micro-1 plc but I dont have the cable, is there a way I can do to have my micro plc working as well? or do you have an idea of an adaptor or something i could match with the existing cable I am working with in order to access micro-1?
elevmike
Member
junnel,
Scroll back up to post 18 and click on the link in the post.
Scroll back up to post 18 and click on the link in the post.
junnel
Member
thanks a lot!
raulv131
Member
Here is the diagram
Any words of support are appreciated.....
Any words of support are appreciated.....
Micro1Source
Member
That PDF is right on the mark, I have a cable that uses that
Hello everyone,
I first came across this forum after I bought some idec Micro-1 PLC's. I have yet to do anything with them. The reason I'm posting is that I have a copy of WindLDR v1.0 and I also have a cable with the converter circuit shown in the schematic pdf above, I can post some pictures and even a board trace if I get time. Would this be of any help?
Hello everyone,
I first came across this forum after I bought some idec Micro-1 PLC's. I have yet to do anything with them. The reason I'm posting is that I have a copy of WindLDR v1.0 and I also have a cable with the converter circuit shown in the schematic pdf above, I can post some pictures and even a board trace if I get time. Would this be of any help?
craig_avanzar
Member
Micro1Source,
If you don't get a response to this thread try opening a new one since this one is a few years old. I wish I had the info you need.
If you don't get a response to this thread try opening a new one since this one is a few years old. I wish I had the info you need.
Similar Topics
Hello,
I am a new member. I use an old automatic wood oven. Its controlled with a IDEC Micro-1 PLC. There is now a mistake.
When I switch on the...
Joe here from Palm Gaming- hoping to find some help here-
we run a custom made heat press- we make ***** chips for casinos- the press has the orig...
I have a machine that is new to our plant that has a Idec Micro 3 FC2A-C24A1 processor. Does anyone know if WindLDR ver 4.2 will talk to this...
I am working on a project and was curiouse if anyone knew or knew where i could find the schematics for the Micro-1 and Micro-1 expansion plc's...
Hello there!
Need help for micro-1 idec plc interface pinout. Units were obsolete and it seems quite hard to find means to access such PLC...