CTC-GUY
Member
Hi,
I Think I Might Have 1 Problem(s) w/MSG Logic, Never Used MSG's Before.
This Is a Home Training Project, To Get This Far Took Some Learning Curve.
HMI Requires w/Ethernet-ABEN (Allen Bradley Driver) MSG's, Bootp Not Supported w/ABEN
AB.com Seach For ABEN Nothing/Maybe w/a Tech Connect Acct, Which Work No Longer Supports.
Thanks To All For Viewing & Helping
Already Established a DF1 RS232 Network w/ML1400 & HMI Works Perfect
Also a WiFi Only w/PC & ML1400-Working
Wanted To Attempt The Ethernet Network w/HMI-Ethernet/Uncharted Waters!
Using w/The HMI Ethernet Port:
PLC Sending/Write-MSG Data, Present In Nxx:x Image Table
CTC-P41/HMI: Allen Bradley Driver [ABEN] Correct Version/Verified w/Parker Automation/CTCUSA
(Interact v7.0 : EX-83153-611 EX-83151-613)
HMI Not Displaying Write Data.
MSG Write Error Code (Hex)d6 (Reserved w/AB)
MSG-READ Same Thing, Not Showing In PLC Nxx:x
MSG Read Error Code (Hex)d6 (Reserved w/AB)
RUN/CMD/IPConfig /all
RS500 Ethernet Network [DHCP] Working/All Nodes-0-2(HMI) 10/100-T Based-TX(F/H) Incl: Pinging
On Both RSlinks [v2.54] Networks, AB_ETH & AB_ETH_TCPIP
From PC-ETH/LinkSys WGT54GS v7.0/Hirschmann Spider 5TX Rail Switch/ML1400-CH1/CTC-P41 HMI/ETH-Port
(Rail Switch, 5 x 10/100BASE-TX, TP cable, RJ45 sockets, auto-crossing, auto-negotiation, auto-polarity)
Addtl Specs:
ML1400 (Label) 1766-L32BXB Ser B FW 11
RS500/Processor Status/Proc [Tab]
OS Series B
OS FRN 13.0
Processor Cat# 1766-LEC
Processor Series B
Processor FRN 3.0
RS500 v8.31.01 (CPR9)
RSLink v2.54
CTC P41-3T7-I1-2A3 (10" P266Mhz,32bit,CF&IDE-SSD, CDROM, 144MB Floppy, 4 Expansion Slot BUS)
Can Submit PLC RS500 .RSS Program, @This Time, Noticed I Need To zip It.
Would Like Someone To Review Logic & See If Logic Is Good or Not
Thanks
Will Edit Post ASAP w/PLC Program zip file
I Think I Might Have 1 Problem(s) w/MSG Logic, Never Used MSG's Before.
This Is a Home Training Project, To Get This Far Took Some Learning Curve.
HMI Requires w/Ethernet-ABEN (Allen Bradley Driver) MSG's, Bootp Not Supported w/ABEN
AB.com Seach For ABEN Nothing/Maybe w/a Tech Connect Acct, Which Work No Longer Supports.
Thanks To All For Viewing & Helping
Already Established a DF1 RS232 Network w/ML1400 & HMI Works Perfect
Also a WiFi Only w/PC & ML1400-Working
Wanted To Attempt The Ethernet Network w/HMI-Ethernet/Uncharted Waters!
Using w/The HMI Ethernet Port:
PLC Sending/Write-MSG Data, Present In Nxx:x Image Table
CTC-P41/HMI: Allen Bradley Driver [ABEN] Correct Version/Verified w/Parker Automation/CTCUSA
(Interact v7.0 : EX-83153-611 EX-83151-613)
HMI Not Displaying Write Data.
MSG Write Error Code (Hex)d6 (Reserved w/AB)
MSG-READ Same Thing, Not Showing In PLC Nxx:x
MSG Read Error Code (Hex)d6 (Reserved w/AB)
RUN/CMD/IPConfig /all
RS500 Ethernet Network [DHCP] Working/All Nodes-0-2(HMI) 10/100-T Based-TX(F/H) Incl: Pinging
On Both RSlinks [v2.54] Networks, AB_ETH & AB_ETH_TCPIP
From PC-ETH/LinkSys WGT54GS v7.0/Hirschmann Spider 5TX Rail Switch/ML1400-CH1/CTC-P41 HMI/ETH-Port
(Rail Switch, 5 x 10/100BASE-TX, TP cable, RJ45 sockets, auto-crossing, auto-negotiation, auto-polarity)
Addtl Specs:
ML1400 (Label) 1766-L32BXB Ser B FW 11
RS500/Processor Status/Proc [Tab]
OS Series B
OS FRN 13.0
Processor Cat# 1766-LEC
Processor Series B
Processor FRN 3.0
RS500 v8.31.01 (CPR9)
RSLink v2.54
CTC P41-3T7-I1-2A3 (10" P266Mhz,32bit,CF&IDE-SSD, CDROM, 144MB Floppy, 4 Expansion Slot BUS)
Can Submit PLC RS500 .RSS Program, @This Time, Noticed I Need To zip It.
Would Like Someone To Review Logic & See If Logic Is Good or Not
Thanks
Will Edit Post ASAP w/PLC Program zip file