LIVE PLC Questions And Answers

Feel free to ask any PLC RELATED question here. If you know the answer to an existing question, help everyone by posting an answer. Enjoy!!!
  • Locked
  • Sticky
Hi folks, If you're having any login issues kindly send an email to [email protected] or use the 'contact us' link on the bottom of every page to get...
Replies
0
Views
1,802
Hi, Am trying to set up the Analog input card channels to 4 -20mA and 0 to 20 mA, but am not able to find the percentage range values under the...
Replies
0
Views
1
Hey all, Still trying to figure all this out... I have an existing AL1122 on a piece of equipment - they would like me to add the DV2300 stack...
Replies
5
Views
114
Recently had to balance a booster pump pressure air bladder tank after discovering the air pressure out of balance and wanted to see how big an...
Replies
4
Views
277
I am trying to Create a Display that shows the time remaining before a timer is Done. To figure out how much time is left before a timer is done...
Replies
1
Views
31
Hello everyone, I will be an EE senior (BS) next fall, and I want to eventually work for a system integrator in industrial controls. Over the...
Replies
7
Views
91
Hello, I have a 1734-AENT POINT I/O with 1734-IE2V in it and I have noticed that the accuracy of the value is low at low voltage. For example...
Replies
0
Views
13
Hello all. I am having issues with controlling an air driven liquid piston pump when using different volume outlet test hoses. For context, this...
Replies
14
Views
197
We weld the top cover on large transformers, is it possible to damage any electrical components or connections in these tanks if the ground cable...
Replies
1
Views
39
I want to scale the raw input from the thermocouple card and convert it to a readable number. Previously I was using a Micrologix 1400...
Replies
5
Views
172
Gents, Will these three work together? I noticed when I went to create add module, it was not listed. Only talking about the safety modules. I...
Replies
25
Views
424
Hi, I'm using a CompactLogix 5069-L320ER with the following I/O in this order on the chassis: Slot 0 - 5069-L320ER Slot 1 - 5069-IA16 (AC Input)...
Replies
4
Views
64
Hi everyone, I am working on a log in/out screen and I want to have a numeric display of the time left until inactivity returns it to default...
Replies
1
Views
48
Hi all, hoping someone might know or have seen this. We have a Quanitum we are trying to get setup for some development. Its part number is 140...
Replies
0
Views
27
I've only done about a dozen full projects but I can not for the life of me stop getting completely destroyed everytime I try to turn a gd servo...
Replies
8
Views
218
If you were to add a card to 1734-AENT before it is added in the logic, will this cause any kind of controller fault on the remote I/O or the PLC...
Replies
4
Views
65
Hi All, can anyone help me with clearing data from the input that has given by the Scanner. (Clear Buffer) I tried COP and MOV instruction to...
Replies
12
Views
295
Hello, so I am working on checking through I/O on a new project. While I was doing this I noticed that the electricians had ran multiple 2c tray...
Replies
4
Views
64
Hello all, my issue:- i have a machine running on a 1756-l55 rack 0 with multiple 1794-asb rio racks connected, im simply trying to replace one...
Replies
2
Views
58
Hi Everyone, i'm facing an issue with the activex datalogging. I'm retrieving the right values but the date and time are in US format and i need...
Replies
0
Views
36
Crimson 3.0 build 579.003, programming a G308A210. I have a display page set up as a master slide. I have the usual alarm banner across the...
Replies
24
Views
5,809
Hello everyone. I have been getting bogged down with some quotations I need to get out. My question is if anyone has a example or "rule of thumb"...
Replies
14
Views
7,788
Hi, Has anyone programmed a job for American Axle? If so, how mucch it extra time would you say it added to your project? How long did it take...
Replies
3
Views
255
Hello We have a Siemens S7 - 300 with 2 Profibus Ports with 4 Remote IO (Wago) and OP 270. The CPU and all remote IOs have Bus Fault and also SF...
Replies
3
Views
77
Has anyone successfully installed and written code to utilize an AMCI NXAE2 Resolver Module? I'm working with a 5089-L340ERS2 PLC and have...
Replies
2
Views
59
Back
Top Bottom