Hello,
I am looking for help about Siemens SM326 module.
I am trying to configure hardware for the following set:
CPU315F-2DP, CP340x2, SM322x1, IM360/361, SM326 DI24xDC24VCx2, SM326 DOxDC24V/2A using Step 7 5.3SP3 + package DS5.4 + F-config 5.5SP1
I have no problem in configuring any of the above mentioned modules except the last one.
In standard mode I get the following errors:
Diagnostic buffer of module DO10xDC24V/2A
Order No./ Description Component Version
6ES7 326-2BF01-0AB0 Hardware 3
- - - Firmware V 2.0.7
Rack: 1
Slot: 6
Event 1 of 1: Event ID 16# F580:8006
Module not Assigned Parameters
Internal error, Incoming event
In safety mode what I get is:
Diagnostic buffer of module DO10xDC24V/2A
Order No./ Description Component Version
6ES7 326-2BF01-0AB0 Hardware 3
- - - Firmware V 2.0.7
Rack: 1
Slot: 6
Event 1 of 3: Event ID 16# F980:8031
Loss of Communication
External error, Incoming event
Event 2 of 3: Event ID 16# F980:0201
Monitoring time for data message frame exceeded
External error, Incoming event
Event 3 of 3: Event ID 16# F580:8006
Module not Assigned Parameters
Internal error, Incoming event
I have simplified my program so that it is generally blank (not to influence hardware).
I get the same errors on three other SM326 DO10xDC24V/2A module instances so the problem should not be with the hardware.
I have looked on any parameters that I could set in the modules:
- in standard mode the bottom switches are set all to 0/ in safety mode they are set to the address
- diagnostic interrupt: does not influence the error
- disable light test: does not influence the error
Simplifying PLC to CPU315F-2DP + SM326 DO10xDC24V/2A (no other modules installed) does not solve the problem.
Does anyone have any idea/experience what should I do in this case?
Thanks and regards
Radek
I am looking for help about Siemens SM326 module.
I am trying to configure hardware for the following set:
CPU315F-2DP, CP340x2, SM322x1, IM360/361, SM326 DI24xDC24VCx2, SM326 DOxDC24V/2A using Step 7 5.3SP3 + package DS5.4 + F-config 5.5SP1
I have no problem in configuring any of the above mentioned modules except the last one.
In standard mode I get the following errors:
Diagnostic buffer of module DO10xDC24V/2A
Order No./ Description Component Version
6ES7 326-2BF01-0AB0 Hardware 3
- - - Firmware V 2.0.7
Rack: 1
Slot: 6
Event 1 of 1: Event ID 16# F580:8006
Module not Assigned Parameters
Internal error, Incoming event
In safety mode what I get is:
Diagnostic buffer of module DO10xDC24V/2A
Order No./ Description Component Version
6ES7 326-2BF01-0AB0 Hardware 3
- - - Firmware V 2.0.7
Rack: 1
Slot: 6
Event 1 of 3: Event ID 16# F980:8031
Loss of Communication
External error, Incoming event
Event 2 of 3: Event ID 16# F980:0201
Monitoring time for data message frame exceeded
External error, Incoming event
Event 3 of 3: Event ID 16# F580:8006
Module not Assigned Parameters
Internal error, Incoming event
I have simplified my program so that it is generally blank (not to influence hardware).
I get the same errors on three other SM326 DO10xDC24V/2A module instances so the problem should not be with the hardware.
I have looked on any parameters that I could set in the modules:
- in standard mode the bottom switches are set all to 0/ in safety mode they are set to the address
- diagnostic interrupt: does not influence the error
- disable light test: does not influence the error
Simplifying PLC to CPU315F-2DP + SM326 DO10xDC24V/2A (no other modules installed) does not solve the problem.
Does anyone have any idea/experience what should I do in this case?
Thanks and regards
Radek
