Need A Help ! ( Fanuc Drive ) - PLCS.net

Mohamed Mamdoh · September 22nd, 2019, 08:37 AM

Hi All ,

I have a Fanuc Robot System(R-30iA) with a drive ( FANUC A05B-2500-C001 ) , and I need to Know how to upload \ Download a backup from\ to it .

Please , Help me understanding this .

Attached a photo of its type .

Thank you .

Liam Moran · September 22nd, 2019, 11:49 AM

A05B-2500-C001 Is not a drive but the housing which contains the robot PSU and CPU. I cannot see your attachment

Mohamed Mamdoh · September 23rd, 2019, 03:03 AM

Ok , I have a problem with it .
the battery was low and when we change it the program didn’t start , and the 7-segment give me the number "1" which mean that we have a proplem in "SRAM" and we need to download the program again to it .

How can I do this ?

I attached a photos again .

gunjstridev · December 8th, 2019, 08:04 AM

You need to do an AoA (All of Above) backup.

You have to insert an USB, Memory Card, etc. on the Teach Pendant or Controller, on the Teach Pendant press "Menu", then go to File. There you will set up your device depending on what type of memory you are using. You can create a directory folder and on the "Backup" option (I think it's F4) look for "All of above" and it will start the program back up.

It is also suggested to do an Image back up, it is done the same way, I just suggest you to do it in different folders so you don't mix your files.

I always take an Image backup AND an All of the Above backup, just in case. You can restore from just about any catastrophe with an image backup.

It will depend on your equipment. RJ2 will need KFloppy and specialized cables.

https://forum.diy-robotics.com/hc/en...t_360008589691

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Topics
Thread	Thread Starter	Forum	Replies	Last Post
Simovert Master Drive -Profibus Enabling Running Problem	Engrtalha	LIVE PLC Questions And Answers	5	June 9th, 2017 07:39 PM
OT: Fugi (Fuji) Drive Terminals from Fanuc Controlled Machine	504bloke	LIVE PLC Questions And Answers	4	March 16th, 2013 02:36 PM
ultraware - enable input active	ubuandy	LIVE PLC Questions And Answers	2	October 25th, 2009 06:08 PM
AB MO2AE & Yaskawa SGM drive	kenschunk	LIVE PLC Questions And Answers	1	September 23rd, 2006 08:25 PM
AC Drive troubles	OkiePC	LIVE PLC Questions And Answers	25	September 8th, 2005 11:21 AM



This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc.
*Try our online PLC Simulator- FREE. Click here now to try it.* ---------->>>>>Get FREE PLC Programming Tips

September 22nd, 2019, 11:49 AM	#2
Liam Moran Lifetime Supporting Member Join Date: May 2011 Location: Carlow Posts: 332	A05B-2500-C001 Is not a drive but the housing which contains the robot PSU and CPU. I cannot see your attachment

December 8th, 2019, 08:04 AM	#4
gunjstridev Member Join Date: Dec 2019 Location: Ahmedabad Posts: 2	You need to do an AoA (All of Above) backup. You have to insert an USB, Memory Card, etc. on the Teach Pendant or Controller, on the Teach Pendant press "Menu", then go to File. There you will set up your device depending on what type of memory you are using. You can create a directory folder and on the "Backup" option (I think it's F4) look for "All of above" and it will start the program back up. It is also suggested to do an Image back up, it is done the same way, I just suggest you to do it in different folders so you don't mix your files. I always take an Image backup AND an All of the Above backup, just in case. You can restore from just about any catastrophe with an image backup. It will depend on your equipment. RJ2 will need KFloppy and specialized cables. https://forum.diy-robotics.com/hc/en...t_360008589691

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)