MitsM83
Member
Hello all,
I have 7 Q series PLCs on a Melsec net/h network, Ladder Programming none of that fancy smancy ST stuff LOL
. Were running the QJ71LP21-25. Now to keep it short I have used all most all my devices in my Network Range Assignment. I can not set up low speed range as I do not have enough Link relays and registers at all stations. No memory for more devices just trust that I can not do it... However I have an abundance of File Registers ( no I cant buy B or W in the PLC File params, well I can but it wont help because only one CPU is UDE the rest are H.)
I have a project in which I must see about 50 words for each Station at every Station. I figured while I am setting up a Transient Transfer I will make a bunch of extra room for future updates and junk.
My answer good or bad, is to set up some Send/Recv commands and do some Transient Transfer. I think I have it just about all figured out just a few questions.
I have two manuals I have been getting my info from Q MELSECNET/H Network System Reference Manual ( I think SHNA080049) and the Melsecnet/h training manual.
1.Any one have any better manuals that better cover transient transfer? Or that are new enough to mention GX Works2 instead of Developer?
2. Is there a max device for each send/recv? (I keep thinking it is 980 per station but no idea where I got this number)( I will increase the max # of transients in the supplementary settings under network range...)
3. Any precautions or advice like, Hey don't do this, I did this once and....
4. It looks like as long as I use different logical channels for each station I should be able to send and receive multiple "messages" at once with no error?? (I will test this and look for the "no room in receive buffer area f222 error)
5. Will this slow down the Cyclic transfers (I will be watching the SW006D and so on to make sure it does not slow my regular transmission down.)
6. I will be using several special relays and registers in the program of course. Any I should use that are not obvious?
I have 7 Q series PLCs on a Melsec net/h network, Ladder Programming none of that fancy smancy ST stuff LOL
. Were running the QJ71LP21-25. Now to keep it short I have used all most all my devices in my Network Range Assignment. I can not set up low speed range as I do not have enough Link relays and registers at all stations. No memory for more devices just trust that I can not do it... However I have an abundance of File Registers ( no I cant buy B or W in the PLC File params, well I can but it wont help because only one CPU is UDE the rest are H.)I have a project in which I must see about 50 words for each Station at every Station. I figured while I am setting up a Transient Transfer I will make a bunch of extra room for future updates and junk.
My answer good or bad, is to set up some Send/Recv commands and do some Transient Transfer. I think I have it just about all figured out just a few questions.
I have two manuals I have been getting my info from Q MELSECNET/H Network System Reference Manual ( I think SHNA080049) and the Melsecnet/h training manual.
1.Any one have any better manuals that better cover transient transfer? Or that are new enough to mention GX Works2 instead of Developer?
2. Is there a max device for each send/recv? (I keep thinking it is 980 per station but no idea where I got this number)( I will increase the max # of transients in the supplementary settings under network range...)
3. Any precautions or advice like, Hey don't do this, I did this once and....
4. It looks like as long as I use different logical channels for each station I should be able to send and receive multiple "messages" at once with no error?? (I will test this and look for the "no room in receive buffer area f222 error)
5. Will this slow down the Cyclic transfers (I will be watching the SW006D and so on to make sure it does not slow my regular transmission down.)
6. I will be using several special relays and registers in the program of course. Any I should use that are not obvious?
