Karinrinkashi
Member
Hello everyone!
It is 1 AM here and i am still at work. Mostly because of our filler issues, but then those got extended to my 1761 ENI NET switch with a red fault light on and i tried resetting it but nothing happened. Then someone walked by and flipped the switch and power cycled it (just like i had been doing for hours) and the fault went away. So the victory was stolen form under my nose.
I decided to take a new 1761 ENI NET switch and configure it with the settings from the old one and see if that one faults out too sometime. I downloaded a Comm Port Something software and then i downloaded the ENI Utility. After 30 minutes of following the manual instructions and then following them AGAIN and AGAIN, BAM! i was able to connect to the switch. I put in the IP address from the old one 199199199140 and subnet 2552552550 and the flashing red fault light (no ip assigned) went away. Then me being an idiot and not accepting this small little victory, i decided to hook upto it again using the utility, this time i exported the info out of the 1761 eni just to make sure that ip address was correct ( i had already checked it from RSLinx, but stupid me). As i extracted the info, i saw the BOOTTP checked and then i noticed "always" and "Fallback" options available. I quickly went to the manual and read about them. I checked "Fallback" option and downloaded the settings to the ROM of ENI. AND BAM! Red flashing light started again, this time with comm port error, and the utility not being able to connect at all. My ethernet cable flashes greens as if communicating well, my utility says connecting and shows progress and bam! the ethernet on 1761 shows amber lights, and i lose connection. The red fault light goes from flashing red to solid to off to MOSTLY flashing red. There is no way to factory reset this damn thing, i think. So what can i do? How can i undo whatever i did? I should have just left it alone after putting in the IP address but i was so excited to configure it!
The utility keeps giving me error on Com port as in invalid comm port. But i used the same one! I deleted all drivers from Linx, deleted all ports from comm port redirector, uninstalled the comm port redirector software, and then followed the whole thing again. NO LUCK! The port rs232 lights keep blinking without any cable, RX light blinks as if possessed, the ethernet port light blinks amber when no ethernet present. Fault light goes away sometimes but mostly flashing.
WHAT IS GOING ON? PLEASE HELP!
It is 1 AM here and i am still at work. Mostly because of our filler issues, but then those got extended to my 1761 ENI NET switch with a red fault light on and i tried resetting it but nothing happened. Then someone walked by and flipped the switch and power cycled it (just like i had been doing for hours) and the fault went away. So the victory was stolen form under my nose.
I decided to take a new 1761 ENI NET switch and configure it with the settings from the old one and see if that one faults out too sometime. I downloaded a Comm Port Something software and then i downloaded the ENI Utility. After 30 minutes of following the manual instructions and then following them AGAIN and AGAIN, BAM! i was able to connect to the switch. I put in the IP address from the old one 199199199140 and subnet 2552552550 and the flashing red fault light (no ip assigned) went away. Then me being an idiot and not accepting this small little victory, i decided to hook upto it again using the utility, this time i exported the info out of the 1761 eni just to make sure that ip address was correct ( i had already checked it from RSLinx, but stupid me). As i extracted the info, i saw the BOOTTP checked and then i noticed "always" and "Fallback" options available. I quickly went to the manual and read about them. I checked "Fallback" option and downloaded the settings to the ROM of ENI. AND BAM! Red flashing light started again, this time with comm port error, and the utility not being able to connect at all. My ethernet cable flashes greens as if communicating well, my utility says connecting and shows progress and bam! the ethernet on 1761 shows amber lights, and i lose connection. The red fault light goes from flashing red to solid to off to MOSTLY flashing red. There is no way to factory reset this damn thing, i think. So what can i do? How can i undo whatever i did? I should have just left it alone after putting in the IP address but i was so excited to configure it!
The utility keeps giving me error on Com port as in invalid comm port. But i used the same one! I deleted all drivers from Linx, deleted all ports from comm port redirector, uninstalled the comm port redirector software, and then followed the whole thing again. NO LUCK! The port rs232 lights keep blinking without any cable, RX light blinks as if possessed, the ethernet port light blinks amber when no ethernet present. Fault light goes away sometimes but mostly flashing.
WHAT IS GOING ON? PLEASE HELP!
Last edited: