Kinetics 6000-fiber; how to jumper out a drive? - PLCS.net

jdbrandt · September 21st, 2022, 01:57 PM

{Old Indramat guy here} (*)
How do you 'jumper out', logically, a drive on a Kinetics 6000?

For example, I have a Power Module (Node 20) and three axis modules (Nodes 22, 24, 26), and want to isolate Node 26.
I move the last fiber connector, eliminating the last axis module, but completing the loop.
Logically, I should be (*) able to just disable/inhibit Node 26.

Nothing I tried worked.

What am I doing wrong?

DarrylR · September 21st, 2022, 02:22 PM

I think you need to remove the axis from the motion group as well.

DarrylR · September 21st, 2022, 03:32 PM

On second thought I think you are correct. You should be able to simply inhibit the axis and be good to go. I also think you would need to leave all the fiber connections as is.

mike3475 · September 22nd, 2022, 09:47 AM

you can go offline to ungroup this axis, then download to controller. If you want to put it back in motion group, you can group it again in offline then download to controller.

September 21st, 2022, 01:57 PM	#1
jdbrandt Lifetime Supporting Member Join Date: Oct 2002 Location: Pennsylvania Posts: 1,196	Kinetics 6000-fiber; how to jumper out a drive? {Old Indramat guy here} () How do you 'jumper out', logically, a drive on a Kinetics 6000? For example, I have a Power Module (Node 20) and three axis modules (Nodes 22, 24, 26), and want to isolate Node 26. I move the last fiber connector, eliminating the last axis module, but completing the loop. Logically, I should be () able to just disable/inhibit Node 26. Nothing I tried worked. What am I doing wrong? __________________ Jeffrey D.Brandt

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Topics
Thread	Thread Starter	Forum	Replies	Last Post
Abb Ac Drive	rajendrad	LIVE PLC Questions And Answers	13	November 5th, 2006 11:18 AM
Heller milling machine controls and drive	naveen	LIVE PLC Questions And Answers	8	August 22nd, 2006 09:40 AM
ac drives	lumbee 100	LIVE PLC Questions And Answers	8	February 8th, 2006 02:10 PM
AB Drive Tools(V2.06) W/SC 300 Interface	Vietnam Bob	LIVE PLC Questions And Answers	0	November 20th, 2002 10:19 PM
Off topic - personal rant!!	PLucas	LIVE PLC Questions And Answers	11	September 9th, 2002 09:25 PM



This board is for PLC Related Q&A ONLY. Please DON'T use it for advertising, etc.
*Try our online PLC Simulator- FREE. Click here now to try it.*

September 21st, 2022, 02:22 PM	#2
DarrylR Member Join Date: Nov 2019 Location: illinois Posts: 110	I think you need to remove the axis from the motion group as well.

September 21st, 2022, 03:32 PM	#3
DarrylR Member Join Date: Nov 2019 Location: illinois Posts: 110	On second thought I think you are correct. You should be able to simply inhibit the axis and be good to go. I also think you would need to leave all the fiber connections as is.

September 22nd, 2022, 09:47 AM	#4
mike3475 Member Join Date: Feb 2013 Location: brooklyn ,NY Posts: 297	you can go offline to ungroup this axis, then download to controller. If you want to put it back in motion group, you can group it again in offline then download to controller.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)