Feel free to ask any PLC RELATED question here. If you know the answer to an existing question, help everyone by posting an
answer.
Enjoy!!!
Hi All,
How do I set a password to PLC using Proficy machine software 9.5-9.8 or some other way?
I as using Emerson CPE305 CPU.
Thanks.
Hi legends, new to this industry but absolutely loving it.
I am looking to go online with a ControlLogix PLC, the network is supported by a...
Good day, we have 15 analog inputs, we need to log the data in excel and monitor these values through web browser. We're planning to go with Delta...
Dear all,
I have fx3u series plc with built in rs422 port and usb-sc09-fx cable. I have a a hyperterminal like application to send and receive...
Hi Experts,
I would like to make firmware upgrade from v3.0 to v4.5 (S7-1200 CPU 1215C).
Can I do it from v3.0 to v4.5?
Do I need to take some...
Hello,
I'm having problems with a BeR X20 BC 0043 module.
The LED flashes twice green and once red. Reading the manual, I believe that this...
Hi. I'm struggling with configuration of PN-PN coupler 6ES7 158-3AD10-0XA0.
The situation is as follows:
I have 1 S7-300 PLC on the X2 part of...
What is the production life of one of these controllers. One of our machines is 4 years old and our supplier is saying the controllers need to be...
Dears,
i am trying to change the series of encoder from A to B, but the program do not has this option (Rslogix5000, 20.06
the old encoder was...
I had a 5/01 CPU give a CPU Fault. It lost the program and I was not able to establish communication with it. I replaced it with a 5/03 we had in...
I can't seem to figure out how to add descriptors to I/O points on an RMC using PCCU.
Say, for example, I want to use "Valve_1" as a descriptor...
So to start off: I have no experience with PLC's, but I'm good at figuring stuff out, but I need some help to know if my PLC is just dead in the...
Hi, I have a Mettler Toledo IND780 (AB-RIO) and a SLC5/04 with a 1747-sn RIO Scanner card. I have lost the configuration for the Ind780...
Hi Everyone,
I replaced encoder 842D-60131331BXA with a new same part number. Dip switches and Preset Push button are considered.
When I tested...
I want to pick up an Allen Bradley PLC so I can practice writing programs. I have 10 years as a maintenance tech and a good understanding of...
Hi,
I am using CM_CAN in my project in Transparent mode. The CAN modules needs transmit 240 message definitions each of 8 bytes, 168 message...
I have a program that does a 7 second "scan" sensor calibration routine whenever a setting (setting is called assistance level or "AL" and ranges...
I have inherited a system that uses a Parker ACR9000 motion controller with the Ethernet PowerLink option that it uses to control five Parker...
Hello everyone, can anyone help me with covert the STL code to ladder.
Iam using plc s71200.
A %DB1.DBX33.7 // angel of vaccum...
Hi.
I'm using a Modbus ProSoft where I basically map data to a big INT array.
Example, where GX_I_63HPU is a REAL, MNETC.DATA.WriteData[200] an...
Hi all,
So I continue to dabble in PLC's and for the most part can figure stuff out. I have been fortunate enough lately to have access to a...
Hi , I am trying to replace an old inverter with a new one and its giving me issues . Once the new one was installed , the S7-300 PLC started...
Hello,
I have a running project on Citect v5.42 and simatic net v6.4
I have created a new spare PC and loaded all software like Citect, station...
Dear Members,
Hello, we are working on a project and facing an issue with the plantpax 5 PMTR library, we have a bidirectional motor, which has 2...
Hello:
I am confused about the A510 modbus addressing scheme. According to Teco's communication addendum the modbuss register addresses start at...